中国科学院机构知识库网格
Chinese Academy of Sciences Institutional Repositories Grid
首页 机构 成果 学者
  
  1. CAS IR Grid
  2. 地质与地球物理研究所
  3. 中国科学院地质与地球物理研究所
  4. 其他部门
Sensitivity of shale anisotropic parameters to core cutting rotation error

文献类型：期刊论文

作者Guo, Shiguang1; Verma, Sumit2; Wang, Qing3,4; Pang, Fei5; Zhang, Kui6; Sun, Haifu7; Zhang, Xiansheng8
刊名EXPLORATION GEOPHYSICS
出版日期2018-10-01
卷号49期号:5页码:775-781
关键词anisotropy cutting error delta shale TTI
ISSN号0812-3985
DOI10.1071/EG16135
英文摘要In laboratories, core cannot always be cut exactly along the axis of symmetry (normal to the bedding plane), which leads to a minor core cutting rotation (CCR) error. The presence of a small CCR error can give rise to an error in computation of anisotropic parameters, which will result in erroneous P-wave and S-wave velocities (V-P, V-SV and V-SH). In this study, we test the sensitivity of Thomson's anisotropic parameters, epsilon (epsilon), gamma () and delta (), to the CCR error. In the vertical transverse isotropy (VTI) system where no rotation exists, values of epsilon, and will not vary with azimuth. Similarly, in VTI the values of V-P, V-SV and V-SH, measured at orientations with respect to the axis of symmetry, will also not vary with azimuth. We modelled and analysed the error generated, in anisotropic parameters and phase velocities, due to rotation error of 5 degrees on VTI ANNIE model data, and the Niobrara Shale core sample measurements. For these two cases, we obtained values of P-wave and S-wave velocities along with anisotropy parameters epsilon, and , at 0 degrees, 45 degrees and 90 degrees orientations with respect to the axis of symmetry, before and after a rotation of 5 degrees, for different azimuth directions. This study shows that, when the CCR error exists, epsilon, and vary with azimuth. For Niobrara Shale samples, we observed that, among all three Thomsen's parameters is the most sensitive parameter to the CCR error; when we varied azimuth, we observed a sign change of from positive to negative. For epsilon and , variation in azimuth lead to only slight changes in values without any change of sign. The CCR error affects V-P and V-s measurements the most at 45 degrees orientation, and the least at 90 degrees orientation. The maximum error occurred at 0 degrees azimuth, whereas the minimum error occurs at 90 degrees azimuth. This analysis suggests that, if core cutting rotation exists, phase velocities should be measured at 90 degrees azimuth for accurate results.
WOS研究方向Geochemistry & Geophysics
语种英语
WOS记录号WOS:000446680100016
出版者CSIRO PUBLISHING
源URL[http://ir.iggcas.ac.cn/handle/132A11/89211]  
专题地质与地球物理研究所_其他部门
通讯作者Wang, Qing
作者单位1.Univ Oklahoma, ConocoPhillips Sch Geol & Geophys, Norman, OK 73019 USA
2.Univ Texas Permian Basin, Dept Phys Sci, Odessa, TX 79762 USA
3.Beijing Informat Sci & Technol Univ, Sch Informat & Commun Engn, Beijing 100101, Peoples R China
4.Chinese Acad Sci, Inst Geol & Geophys, Beijing 100029, Peoples R China
5.China Geol Survey, Ctr Oil & Gas Survey, Beijing 100029, Peoples R China
6.China Natl Petr Corp, Bureau Geophys Prospecting, Zhuozhou 072751, Hebei, Peoples R China
7.Res Inst Hengda Century Geophys Technol Co Ltd, Beijing 100020, Peoples R China
8.SINOPEC, Northwest Oilfield Branch Co, Res Inst Petr Explorat & Prod, Urumqi 830011, Xinjiang, Peoples R China
推荐引用方式
GB/T 7714		 Guo, Shiguang,Verma, Sumit,Wang, Qing,et al. Sensitivity of shale anisotropic parameters to core cutting rotation error[J]. EXPLORATION GEOPHYSICS,2018,49(5):775-781.
APA Guo, Shiguang.,Verma, Sumit.,Wang, Qing.,Pang, Fei.,Zhang, Kui.,...&Zhang, Xiansheng.(2018).Sensitivity of shale anisotropic parameters to core cutting rotation error.EXPLORATION GEOPHYSICS,49(5),775-781.
MLA Guo, Shiguang,et al."Sensitivity of shale anisotropic parameters to core cutting rotation error".EXPLORATION GEOPHYSICS 49.5(2018):775-781.

入库方式： OAI收割

来源：地质与地球物理研究所

浏览0
下载0
收藏0
其他版本

除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。