Mechanical behaviour and the evolution of the dislocation structure of copper polycrystal deformed under fatigue-tension and tension-fatigue sequential strain paths
文献类型：期刊论文
| 作者 | W. P. Jia ; J. V. Fernandes |
| 刊名 | Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing
 |
| 出版日期 | 2003 |
| 卷号 | 348期号:1-2页码:133-144 |
| 关键词 | polycrystal strain path change tension fatigue dislocation structure plastic behavior stress metals sheets steel |
| ISSN号 | 0921-5093 |
| 中文摘要 | Two sequences of tension-fatigue and fatigue-tension tests were performed on copper polycrystal sheet, with a mean grain size of 32 mum. For the angle between the two successive loading directions, two typical values (0 and 45degrees) have been chosen. The effect of strain path change on subsequent initial work hardening rate and saturation stress in tension-fatigue, as well as the effect of strain path change on subsequent yield and flow behaviour in fatigue-tension have been investigated. The strain rate for the tension tests was 5 x 10(-3) s(-1), while the fatigue tests were performed under constant plastic strain amplitude control with different values of amplitudes (epsilon(pl) = 6 x 10(-4), 1.5 x 10(-3), 3 x 10(-3)). Slip morphology and dislocation microstructure were observed by optical and transmission electron microscopy (TEM) after mechanical tests. Under these conditions, in the case of fatigue-tension, it was found that fatigues prestraining influences the subsequent yield and flow behaviour in tension. However, the subsequent mechanical behaviour of samples seems only to be affected by the magnitude of strain path change (namely, the angle between the two successive loading directions), and not by the value of the plastic strain amplitude of the preceding fatigue tests. In the case of tension-fatigue, the strain amount of preloading in tension obviously affects the initial cyclic hardening rate, while it has almost no effect on the saturation stress of subsequent fatigue tests, irrespective of the value of the angle between the two successive loading directions. The occurrence of microbands in the saturation fatigue dislocation structures of samples prestrained in tension implies that fatigue is a more effective loading mode than tension, in causing intense glide on the activated slip systems. The correlation between mechanical properties and microstructural observations is discussed. (C) 2002 Elsevier Science B.V. All rights reserved. |
| 原文出处 | |
| 公开日期 | 2012-04-14 |
| 源URL | [http://ir.imr.ac.cn/handle/321006/35866]  |
| 专题 | 金属研究所_中国科学院金属研究所 |
| 推荐引用方式 GB/T 7714 | W. P. Jia,J. V. Fernandes. Mechanical behaviour and the evolution of the dislocation structure of copper polycrystal deformed under fatigue-tension and tension-fatigue sequential strain paths[J]. Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing,2003,348(1-2):133-144. |
| APA | W. P. Jia,&J. V. Fernandes.(2003).Mechanical behaviour and the evolution of the dislocation structure of copper polycrystal deformed under fatigue-tension and tension-fatigue sequential strain paths.Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing,348(1-2),133-144. |
| MLA | W. P. Jia,et al."Mechanical behaviour and the evolution of the dislocation structure of copper polycrystal deformed under fatigue-tension and tension-fatigue sequential strain paths".Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing 348.1-2(2003):133-144. |
入库方式： OAI收割
来源：金属研究所
浏览0
下载0
收藏0
其他版本
除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。