Influence of cutting conditions on the cutting performance of TiAl6V4
文献类型：会议论文
| 作者 | Ye GG(叶贵根); Xue SF; Tong XH; Dai LH(戴兰宏) |
| 出版日期 | 2011 |
| 会议名称 | International Conference on Materials and Products Manufacturing Technology (ICMPMT 2011) |
| 会议日期 | OCT 28-30, 2011 |
| 会议地点 | Chengdu, PEOPLES R CHINA |
| 通讯作者邮箱 | Yegg@lnm.imech.ac.cn; lhdai@lnm.imech.ac.cn |
| 关键词 | Chip morphology Size effect Cutting temperature TiAl6V4 CHIP FORMATION ALLOY SIMULATION TI-6AL-4V |
| 卷号 | 337 |
| 页码 | 387-391 |
| 通讯作者 | Dai, LH (reprint author), Chinese Acad Sci, State Key Lab Nonlinear Mech, Inst Mech, Beijing 100190, Peoples R China. |
| 中文摘要 | The FEM simulation was developed to investigate the influences of cutting speed, uncut chip thickness and tool rake angle on the cutting performance of TiAl6V4. The FEM simulation was validated using experimental results and good agreement was obtained. The simulation results indicate that the transition from continuous to saw-tooth chip formation is favored by increases in cutting speed and uncut chip thickness and a decrease in tool rake angle. The existence of Salomon's assumption was further discussed, which shows that the Salomon's assumption is not valid for the tool-chip interface temperature, but could be true for the surface temperature of the workpiece. In addition, decreasing the uncut chip thickness leads to an increase of the specific cutting energy, which could be primarily caused by an increase in the shear strength of the workpiece material due to a decrease in the PSZ temperature. |
| 收录类别 | CPCI ; EI |
| 合作状况 | 国内 |
| 产权排序 | [Ye, GuiGen; Xue, ShiFeng; Tong, XingHua] Department of Engineering Mechanics, Petroleum University of China, Shan Dong 257061, China;[Ye, GuiGen; Dai, LanHong] State Key Laboratory of Nonlinear Mechanics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China |
| 会议网址 | http://dx.doi.org/10.4028/www.scientific.net/AMR.337.387 |
| 会议录 | MATERIALS PROCESSING TECHNOLOGY
 |
| 会议录出版者 | TRANS TECH PUBLICATIONS LTD |
| 学科主题 | Engineering ; Manufacturing; Materials Science ; Multidisciplinary; Materials Science ; Coatings & Films |
| 会议录出版地 | LAUBLSRUTISTR 24, CH-8717 STAFA-ZURICH, SWITZERLAND |
| 语种 | 英语 |
| ISSN号 | 1022-6680 |
| ISBN号 | 978-3-03785-247-7 |
| 源URL | [http://dspace.imech.ac.cn/handle/311007/46821]  |
| 专题 | 力学研究所_非线性力学国家重点实验室 |
| 推荐引用方式 GB/T 7714 | Ye GG,Xue SF,Tong XH,et al. Influence of cutting conditions on the cutting performance of TiAl6V4[C]. 见:International Conference on Materials and Products Manufacturing Technology (ICMPMT 2011). Chengdu, PEOPLES R CHINA. OCT 28-30, 2011.http://dx.doi.org/10.4028/www.scientific.net/AMR.337.387. |
入库方式： OAI收割
来源：力学研究所
浏览0
下载0
收藏0
其他版本
除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。