Experimental study and finite element polycrystal model simulation of the cold rolling textures in a powder metallurgy processed pure aluminum plate
文献类型：期刊论文
| 作者 | Chen, LQ; Kanetake, N |
| 刊名 | JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
 |
| 出版日期 | 2005-03-01 |
| 卷号 | 21期号:2页码:148-154 |
| 关键词 | texture cold rolling aluminium finite element polycrystal model (FEPM) powder metallurgy |
| ISSN号 | 1005-0302 |
| 通讯作者 | Chen, LQ(lqchen@imr.ac.cn) |
| 英文摘要 | Ingot metallurgy (IM) aluminum has long been the subject and attracted the attention of many metallurgists and textural researchers of materials. Due to the introduction of large amounts of ex situ interfaces, however, the textures in powder metallurgy (PM) processed aluminum has been rarely reported. In this article, a pure aluminum plate was prepared via PM route. The starting billet was first produced with uni-axially cold compaction and flat hot-extrusion and then followed by cold rolling processes. The hot-extruded and cold rolling deformation textures of the pure PM aluminum at 50%, 80% and 90% cold rolling reductions were studied by orientation distribution functions (ODFs) analysis. The finite element polycrystal model (FEPM) was finally utilized to simulate the cold rolling textural evolution at various stages of cold rolling. In FEPM simulation, the initial hot-extruded textures were taken into account as inputs. The results showed that typical beta-fiber texture formed in pure PM aluminum with the cold rolling reduction increased till 80%, and there was not much change after excessive cold rolling deformation. Homogeneous slip is not the only deformation mode in PM processed pure aluminum plate at over 80% cold rolling reduction. The experimental results were qualitatively in good agreement with the simulated ones. |
| WOS研究方向 | Materials Science ; Metallurgy & Metallurgical Engineering |
| 语种 | 英语 |
| WOS记录号 | WOS:000228230400002 |
| 出版者 | JOURNAL MATER SCI TECHNOL |
| 源URL | [http://ir.imr.ac.cn/handle/321006/84447]  |
| 专题 | 金属研究所_中国科学院金属研究所 |
| 通讯作者 | Chen, LQ |
| 作者单位 | 1.Chinese Acad Sci, Met Res Inst, Shenyang 110016, Peoples R China 2.Nagoya Univ, Sch Engn, Dept Mat Proc Engn, Chikusa Ku, Nagoya, Aichi 4648603, Japan |
| 推荐引用方式 GB/T 7714 | Chen, LQ,Kanetake, N. Experimental study and finite element polycrystal model simulation of the cold rolling textures in a powder metallurgy processed pure aluminum plate[J]. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY,2005,21(2):148-154. |
| APA | Chen, LQ,&Kanetake, N.(2005).Experimental study and finite element polycrystal model simulation of the cold rolling textures in a powder metallurgy processed pure aluminum plate.JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY,21(2),148-154. |
| MLA | Chen, LQ,et al."Experimental study and finite element polycrystal model simulation of the cold rolling textures in a powder metallurgy processed pure aluminum plate".JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY 21.2(2005):148-154. |
入库方式： OAI收割
来源：金属研究所
浏览0
下载0
收藏0
其他版本
除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。