STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT
文献类型：期刊论文
| 作者 | Li Yongkui2; Quan Chunyi1; Lu Shanping2; Jiao Qingyang1; Li Shijian1; Sun Zhonghai1 |
| 刊名 | ACTA METALLURGICA SINICA
 |
| 出版日期 | 2016-03-11 |
| 卷号 | 52期号:3页码:281-288 |
| ISSN号 | 0412-1961 |
| 关键词 | thin-wall part of TA15 titanium alloy weld deformation post weld heat treatment finite element method |
| 通讯作者 | Lu Shanping(shplu@imr.ac.cn) |
| 英文摘要 | Weld deformation of the thin-wall weldment used in fighter aircraft not only hinders its subsequent procedure of fabrication and assembling, but also reduces its fatigue strength. As a result, weld deformation shortens its service life essentially. Dustpan deformation is always produced in the thin-wall weldment after multiple pass weld. In this work, combining with the experiment, the finite element method was adopted to analysis the deformation of the thin-wall weldment by multiple-pass weld and its shape correction by post weld heat treatment. For obtaining the fundamental properties such as thermal parameters and mechanical parameters of TA15 titanium alloy, a series of experiments were conducted at room temperature and high temperatures. Additionally, creep behaviors of TA15 titanium alloy were studied at the temperatures of 500, 550, 600, 650, 700 and 750 degrees C, and the parameters of creep constitutive equations of the alloy were obtained with considering the analysis of post weld heat treatment. A thermal coupled temperature-displacement analysis for welding and post weld heat treatment was performed on a three dimensional shell model of protective grille. Experiments of multiple-pass weld and post weld heat treatment were used to testify the reliability of the finite element model of welding and post weld heat treatment. With using the reliable finite element model, the parameters of heat treatment were studied. The study indicates that, the fabrication on the crossing of structure section and fillet after fillet-wallboard weld leads the compression deformation release along the fillet, after that, the shrinkage distortion produced during spot welding of fillet-structural section mainly contributes the large dustpan deformation of the thin-wall weldment; increasing temperatures, enlarging loads and prolonging the hold time can improve the shape correction of the thin-wall weldment during post weld heat treatment, hence the guide maps of the post weld heat treatment for shape correction of the thin-wall weldment under 700 and 750 degrees C are worked out. |
| WOS研究方向 | Metallurgy & Metallurgical Engineering |
| 语种 | 英语 |
| 出版者 | SCIENCE PRESS |
| WOS记录号 | WOS:000372691500004 |
| 源URL | [http://ir.imr.ac.cn/handle/321006/121845]  |
| 专题 | 金属研究所_中国科学院金属研究所 |
| 通讯作者 | Lu Shanping |
| 作者单位 | 1.AVIC Shenyang Aircraft Corp, Shenyang 110034, Peoples R China 2.Chinese Acad Sci, Shenyang Natl Lab Mat Sci, Inst Met Res, Shenyang 110016, Peoples R China |
| 推荐引用方式 GB/T 7714 | Li Yongkui,Quan Chunyi,Lu Shanping,et al. STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT[J]. ACTA METALLURGICA SINICA,2016,52(3):281-288. |
| APA | Li Yongkui,Quan Chunyi,Lu Shanping,Jiao Qingyang,Li Shijian,&Sun Zhonghai.(2016).STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT.ACTA METALLURGICA SINICA,52(3),281-288. |
| MLA | Li Yongkui,et al."STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT".ACTA METALLURGICA SINICA 52.3(2016):281-288. |
入库方式： OAI收割
来源：金属研究所
浏览0
下载0
收藏0
其他版本
除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。