Microstructural evolutions and mechanical characteristics of Ti/steel clad plates fabricated through cold spray additive manufacturing followed by hot-rolling and annealing
文献类型：期刊论文
| 作者 | Zhao, Zhipo1,2; Tariq, Naeem ul Haq3; Tang, Junrong1,2; Jia, Cunlei1,2; Qiu, Xiang1,2; Ren, Yupeng1,2; Liu, Hanhui1,2; Shen, Yanfang1; Du, Hao1; Cui, Xinyu1 |
| 刊名 | MATERIALS & DESIGN
 |
| 出版日期 | 2020-01-05 |
| 卷号 | 185页码:11 |
| 关键词 | Ti/steel clad plate Cold spray additive manufacturing (CSAM) Heat treatment Mechanical properties Microstructure |
| ISSN号 | 0264-1275 |
| DOI | 10.1016/j.matdes.2019.108249 |
| 通讯作者 | Wang, Jiqiang(jqwang11s@imr.ac.cn) ; Xiong, Tianying(tyxiong@imr.ac.cn) |
| 英文摘要 | An innovative approach is designed to fabricate Ti/steel clad plates. Instead of using Ti sheets, pure Ti powder was initially deposited on steel plates using cold spray additive manufacturing (CSAM). Then well bonded Ti/steel clad plates were obtained through hot-rolling and annealing operations. The mechanical properties of the clad plates at different processing stages were evaluated by performing a series of tensile tests and shear tests. It was revealed that the Ti/steel clad plates had excellent shear strength (280 Mpa), ultimate tensile strength (UTS, 564 Mpa) and decent elongation (EL,18%). Micro structural investigation of the specimens was performed by scanning electron microscopy (SEM), electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM). It was revealed that cold spraying offers good pre-bonding of Ti with the steel plate thereby suppressing cracking and oxidation at the interface. Hot-rolling treatment repaired the pores/defects in the as-sprayed Ti coating and resulted in metallurgical bonding between Ti particles as well as Ti/steel interface, which remarkably improved the strength of the material. High dislocation density in the clad plates were further eliminated by the annealing treatment through recovery, recrystallization and grain growth mechanisms, which greatly improved the toughness of the samples. (C) 2019 The Authors. Published by Elsevier Ltd. |
| 资助项目 | National Natural Science Foundation of China[51671205] |
| WOS研究方向 | Materials Science |
| 语种 | 英语 |
| WOS记录号 | WOS:000504639400028 |
| 出版者 | ELSEVIER SCI LTD |
| 资助机构 | National Natural Science Foundation of China |
| 源URL | [http://ir.imr.ac.cn/handle/321006/136260]  |
| 专题 | 金属研究所_中国科学院金属研究所 |
| 通讯作者 | Wang, Jiqiang; Xiong, Tianying |
| 作者单位 | 1.Chinese Acad Sci, Inst Met Res, Shenyang 110016, Liaoning, Peoples R China 2.Univ Sci & Technol China, Sch Mat Sci & Engn, Shenyang 110016, Liaoning, Peoples R China 3.Pakistan Inst Engn & Appl Sci, Dept Met & Mat Engn, Islamabad, Pakistan |
| 推荐引用方式 GB/T 7714 | Zhao, Zhipo,Tariq, Naeem ul Haq,Tang, Junrong,et al. Microstructural evolutions and mechanical characteristics of Ti/steel clad plates fabricated through cold spray additive manufacturing followed by hot-rolling and annealing[J]. MATERIALS & DESIGN,2020,185:11. |
| APA | Zhao, Zhipo.,Tariq, Naeem ul Haq.,Tang, Junrong.,Jia, Cunlei.,Qiu, Xiang.,...&Xiong, Tianying.(2020).Microstructural evolutions and mechanical characteristics of Ti/steel clad plates fabricated through cold spray additive manufacturing followed by hot-rolling and annealing.MATERIALS & DESIGN,185,11. |
| MLA | Zhao, Zhipo,et al."Microstructural evolutions and mechanical characteristics of Ti/steel clad plates fabricated through cold spray additive manufacturing followed by hot-rolling and annealing".MATERIALS & DESIGN 185(2020):11. |
入库方式： OAI收割
来源：金属研究所
浏览0
下载0
收藏0
其他版本
除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。