The nature of the maximum microhardness and thickness of the gradient layer in surface-strengthened Cu-Al alloys
文献类型：期刊论文
| 作者 | Ren, C. X.1,2; Wang, Q.2; Hou, J. P.2; Zhang, Z. J.2; Zhang, Z. F.1,2; Langdon, T. G.3 |
| 刊名 | ACTA MATERIALIA
 |
| 出版日期 | 2021-08-15 |
| 卷号 | 215页码:15 |
| 关键词 | Cu-Al alloy Gradient layer Microhardness Microstructure Surface spinning strengthening Yield strength |
| ISSN号 | 1359-6454 |
| DOI | 10.1016/j.actamat.2021.117073 |
| 通讯作者 | Wang, Q.(gmwang@imr.ac.cn) ; Zhang, Z. F.(zhfzhang@imr.ac.cn) |
| 英文摘要 | The presence of a gradient layer with an increased maximum microhardness and extended thickness is extremely attractive because it can enhance the service performances for surface-strengthened metallic materials. In this research, Cu-Al alloys with different Al contents and microstructures were processed by surface spinning strengthening (3S) and studies were conducted to examine the gradient microstructure and microhardness distributions of the 3S Cu-Al alloys. The experimental results show that each group of the 3S Cu-Al alloys having the same Al content has approximately the same maximum microhardness at the topmost surface layer and the maximum microhardness increases with an increase in the Al content. In addition, the thickness of the gradient layer in the 3S Cu-Al alloys increases with a decrease of yield strength and an increase in the work-hardening exponent, respectively. The relationship between the maximum microhardness and chemical composition which determines the Young's modulus and plastic deformation mode, and the relationship between the thickness of the gradient layer and the microstructure which governs the strength and work-hardening capacity, were both investigated. It is found that the maximum microhardness of the gradient layer depends mainly on the chemical composition; whereas the thickness of the gradient layer depends primarily on both the strength and work-hardening capacity which are closely related to the microstructure. By combining the compositional design and microstructure optimization of the materials, and improving the surface strengthening intensity, a gradient layer of the surface-strengthened materials with an enhanced maximum microhardness and an extended thickness may be achieved. (C) 2021 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved. |
| 资助项目 | National Natural Science Foundation of China (NSFC)[U1664253] ; KC Wong Education Foundation[GJTD-2020-09] ; LiaoNing Revitalization Talents Program[XLYC1808027] ; European Research Council[267464-SPDMETALS] |
| WOS研究方向 | Materials Science ; Metallurgy & Metallurgical Engineering |
| 语种 | 英语 |
| WOS记录号 | WOS:000684229400040 |
| 出版者 | PERGAMON-ELSEVIER SCIENCE LTD |
| 资助机构 | National Natural Science Foundation of China (NSFC) ; KC Wong Education Foundation ; LiaoNing Revitalization Talents Program ; European Research Council |
| 源URL | [http://ir.imr.ac.cn/handle/321006/159328]  |
| 专题 | 金属研究所_中国科学院金属研究所 |
| 通讯作者 | Wang, Q.; Zhang, Z. F. |
| 作者单位 | 1.Univ Sci & Technol China, Sch Mat Sci & Engn, Shenyang 110016, Peoples R China 2.Chinese Acad Sci, Shi Changxu Innovat Ctr Adv Mat, Inst Met Res, Shenyang 110016, Peoples R China 3.Univ Southampton, Dept Mech Engn, Southampton SO17 1BJ, Hants, England |
| 推荐引用方式 GB/T 7714 | Ren, C. X.,Wang, Q.,Hou, J. P.,et al. The nature of the maximum microhardness and thickness of the gradient layer in surface-strengthened Cu-Al alloys[J]. ACTA MATERIALIA,2021,215:15. |
| APA | Ren, C. X.,Wang, Q.,Hou, J. P.,Zhang, Z. J.,Zhang, Z. F.,&Langdon, T. G..(2021).The nature of the maximum microhardness and thickness of the gradient layer in surface-strengthened Cu-Al alloys.ACTA MATERIALIA,215,15. |
| MLA | Ren, C. X.,et al."The nature of the maximum microhardness and thickness of the gradient layer in surface-strengthened Cu-Al alloys".ACTA MATERIALIA 215(2021):15. |
入库方式： OAI收割
来源：金属研究所
浏览0
下载0
收藏0
其他版本
除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。