DESIGN AND FABRICATION OF ROCK-BASED MICROFLUIDICS BY 3D PRINTING: THE STRUCTURE CHARACTERIZATION AND PORE-SCALE FLOW EXPERIMENT VALIDATION
文献类型：期刊论文
| 作者 | Wang, Yao4,5; Song, Rui3,4; Sun, Shuyu3; Zhu, Baolong5; Peng, Jiajun2; Pei, Guihong1 |
| 刊名 | JOURNAL OF POROUS MEDIA
 |
| 出版日期 | 2021 |
| 卷号 | 24期号:12页码:77-92 |
| 关键词 | ROC 3D printing waterflooding wettability pore-scale flow |
| ISSN号 | 1091-028X |
| 英文摘要 | Although great progress has been achieved in numerical simulation on porous flow in rock in decades, experiments performed on reservoir-on-a-chip (ROC) have been emphasized as the most sufficient and direct way to investigate the subsurface fluid flow at pore scale. This paper applies the cutting-edge three-dimensional printing (3DP) technique into the fabrication of ROC and the visualized two-phase fluids experiments. The structure of 3D-printed ROC is quantitatively characterized using the surface scanning analyzer and stereomicroscope, and then validated by comparison with the original digital structure. Then immiscible (oil-water) two-phase flow experiments are conducted on the 3D-printed ROC and imaged using the high-resolution camera in real time. The typical fingering phenomenon caused by the heterogeneity of pore-throat structure is observed, and the effects of surface wettability on the interfacial shape evolution are analyzed. Comparing to traditional fabrication methods (e.g., chemical etching and soft lithography), 3D-printed ROC is approved to be a novel approach to manufacture the morphology, topology, and connectivity of the pore network, while reducing the cost and the time required. |
| 资助项目 | Natural Science Foundation of SWUST[20zx7129] ; National Natural Science Foundation of China[51909225] ; National Natural Science Foundation of China[41672342] ; King Abdullah University of Science and Technology (KAUST)[BAS/1/1351-1301] ; China Scholarship Council |
| WOS研究方向 | Thermodynamics ; Engineering ; Mechanics |
| 语种 | 英语 |
| WOS记录号 | WOS:000709776600005 |
| 出版者 | BEGELL HOUSE INC |
| 源URL | [http://119.78.100.198/handle/2S6PX9GI/28400]  |
| 专题 | 中科院武汉岩土力学所 |
| 通讯作者 | Song, Rui |
| 作者单位 | 1.Hubei Business Coll, Sch Construct Econ & Engn Management, Wuhan 430079, Hubei, Peoples R China 2.Chongqing Univ, Sch Resources & Safety Engn, Chongqing 400044, Peoples R China 3.King Abdullah Univ Sci & Technol KAUST, Computat Transport Phenomena Lab CTPL, Thuwal 239556900, Saudi Arabia 4.Chinese Acad Sci, Wuhan Inst Rock & Soil Mech, State Key Lab Geomech & Geotech Engn, Wuhan 430071, Hubei, Peoples R China 5.Southwest Univ Sci & Technol, Sch Civil Engn & Architecture, Mianyang 621010, Sichuan, Peoples R China |
| 推荐引用方式 GB/T 7714 | Wang, Yao,Song, Rui,Sun, Shuyu,et al. DESIGN AND FABRICATION OF ROCK-BASED MICROFLUIDICS BY 3D PRINTING: THE STRUCTURE CHARACTERIZATION AND PORE-SCALE FLOW EXPERIMENT VALIDATION[J]. JOURNAL OF POROUS MEDIA,2021,24(12):77-92. |
| APA | Wang, Yao,Song, Rui,Sun, Shuyu,Zhu, Baolong,Peng, Jiajun,&Pei, Guihong.(2021).DESIGN AND FABRICATION OF ROCK-BASED MICROFLUIDICS BY 3D PRINTING: THE STRUCTURE CHARACTERIZATION AND PORE-SCALE FLOW EXPERIMENT VALIDATION.JOURNAL OF POROUS MEDIA,24(12),77-92. |
| MLA | Wang, Yao,et al."DESIGN AND FABRICATION OF ROCK-BASED MICROFLUIDICS BY 3D PRINTING: THE STRUCTURE CHARACTERIZATION AND PORE-SCALE FLOW EXPERIMENT VALIDATION".JOURNAL OF POROUS MEDIA 24.12(2021):77-92. |
入库方式： OAI收割
来源：武汉岩土力学研究所
浏览0
下载0
收藏0
其他版本
除非特别说明，本系统中所有内容都受版权保护，并保留所有权利。