中国科学院机构知识库网格
Chinese Academy of Sciences Institutional Repositories Grid
油浴润滑高速枢轴承摩擦系数变载荷测量方法

文献类型:期刊论文

作者戴兴建; 唐长亮; 于世强
刊名摩擦学学报
出版日期2011
卷号31期号:1页码:7-11
关键词宝石枢轴承 变载荷 风损 摩擦系数
ISSN号1004-0595
其他题名Measuring Friction Coefficient of the High Speed Pivot Bearing in Oil-bath Lubrication by a Varying Load Method
通讯作者daix@j.tsinghua.edu.cn
中文摘要提出高速枢轴承摩擦系数变载荷测量方法并设计了试验装置,测量得到枢轴承在不同转速下的摩擦系数.各试验枢轴在相同转速下,摩擦系数测量值差别明显,这源于边界润滑的随机性和复杂性;但是各轴摩擦系数均随转速升高而降低,测量平均值在0.09~0.05之间,这表明随枢轴承转速升高,流体动压效应增强,薄膜润滑降低了轴尖与宝石接触概率.通过对轴承摩擦损耗的计算来分析测量方法的可靠性,并将该方法应用于螺旋槽油膜轴承,测得其摩擦系数在0.017~0.014之间
英文摘要A varying load method was presented to measure the friction coefficient of the high speed pivot bearing in oil-bath lubrication. The friction coefficient of the pivot bearing running at different speeds was measured on the test apparatus. The experimental results showed that the friction coefficients of the pivot bearing samples diverged greatly at the same test speed, which was due to the randomness and complexity of the boundary lubrication of the pivot-jewel bearing in oil-bath. However, all of the friction coefficients became smaller when the running speed increased for every pivot bearing sample, and average measured values were between 0.09 and 0.05.The decrease of the friction coefficient with the increasing speed indicated that the hydro-dynamic effect in the boundary lubrication became strong and the thin-film lubrication cut down the probability of surface contact between the pivot and the jewel. The reliability of the measurement method was analyzed by calculating the energy loss from bearing friction. The friction coefficients of a spiral groove oil film bearing used in the flywheel support system were between 0.017 ~ 0.014 by the same test method
学科主题空间技术
收录类别EI ; CSCD
语种中文
CSCD记录号CSCD:4135656
公开日期2014-12-15
源URL[http://ir.nssc.ac.cn/handle/122/3333]  
专题国家空间科学中心_其他部室
推荐引用方式
GB/T 7714
戴兴建,唐长亮,于世强. 油浴润滑高速枢轴承摩擦系数变载荷测量方法[J]. 摩擦学学报,2011,31(1):7-11.
APA 戴兴建,唐长亮,&于世强.(2011).油浴润滑高速枢轴承摩擦系数变载荷测量方法.摩擦学学报,31(1),7-11.
MLA 戴兴建,et al."油浴润滑高速枢轴承摩擦系数变载荷测量方法".摩擦学学报 31.1(2011):7-11.

入库方式: OAI收割

来源:国家空间科学中心

浏览0
下载0
收藏0
其他版本

除非特别说明,本系统中所有内容都受版权保护,并保留所有权利。