中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共4条，第1-4条

帮助

条数/页：排序方式：
	Constant current vs. constant power control in AC resistance spot welding 期刊论文 OAI收割 Journal of Materials Processing Technology, 2015, 卷号: 223, 页码: 299-304 作者: Zhou K(周亢); Cai LL; Yao P 收藏 \| 浏览/下载：19/0 \| 提交时间：2016/04/01 Control strategy Constant current control Constant power control Nugget growth
	Design of programmable near infrared cold light source (EI CONFERENCE) 会议论文 OAI收割 2011 International Conference on Electronics and Optoelectronics, ICEOE 2011, July 29, 2011 - July 31, 2011, Dalian, China 作者: Fu Q.; Wang B.; Wang B.; Wang R. 收藏 \| 浏览/下载：32/0 \| 提交时间：2013/03/25 In the near infrared spectroscopy detector of Charge-coupled Device requires very high stability for light source. We design the cold light source in the measurement of near infrared spectroscopy. Cold light source consists of high-power op amp OPA549 high current constant current source and proportion integral differential (PID) control algorithm. As is shown in the experimental results the method is better the overshoot is very small the stability is excellent in the process of soft-start. While light intensity was able to meet the requirements of near-infrared instruments to measure. 2011 IEEE.
	Novel method for optimizing polishing tool-path in CCOS based on weighted-iterative algorithm (EI CONFERENCE) 会议论文 OAI收割 4th International Symposium on Advanced Optical Manufacturing and Testing Technologies: Advanced Optical Manufacturing Technologies, November 19, 2008 - November 21, 2008, Chengdu, China 作者: Zhang X.-J.; Wang X.; Wang X.; Wang X.; Wang X.-K. 收藏 \| 浏览/下载：44/0 \| 提交时间：2013/03/25 In Computer Controlled Optical Surfacing (CCOS) polishing tool-path is the base of solving other control parameters such as dwell time. In order to improve the fabrication results of polishing off-axis aspheric a novel method to optimize the tool-path is discussed in this paper. The optimizing method named weighted-iterative algorithm is according to the balance principle of the particle system. The power factor of each dwell point represents the requirement of dwell density. Considering the factors which influence the polishing result the power factors cosist of three elements include constant error distribution and dwell distance of workpiece edge. The tool-path is solved by numerical iterative method. In the end an error data is simulated with actual parameters using the matrix-based algorithm with two different tool-paths. The one is X-Y uniform spacing model and the other one is to optimize it based on the first. The comparison shows that the results of the optimized one are much better than traditional one especially the rms convergence rate. Theory of the algorithm is simple and exercisable and it satisfies practical requirement as well. 2009 SPIE.
	All-solid-stated laser controller design based on digital optical feedback (EI CONFERENCE) 会议论文 OAI收割 Lasers in Material Processing and Manufacturing II, November 10, 2004 - November 12, 2004, Beijing, China 作者: Liu L.; Wang J.-L.; Wang J.-L.; Liu L. 收藏 \| 浏览/下载：29/0 \| 提交时间：2013/03/25 The new design about a CW digital all-solid-stated LD pumped Nd:YVO 4 controller is introduced. The stable output power of this digital laser controller which adopts Digital Signal Processor(TMS320C31) is approximately 20mW. The whole system is composed of constant- current source protection circuit pulse-width modulation circuit Si-photo-detector and amplified circuit and Digital Signal Processor control system etc. In terms of error deviation Based on nonlinear control curves of LD power output by Si-photo-detector the region control can be obtained by means of the PID control algorithm in the software platform that is error amendment and high stability laser power output can be achieved. And the precision of temperature control can reduce from 0.2C to 0.04C. By adopted integral separated mode PID control algorithm the LD output power instability ( %) down to 2%. By way of adopting the new digital design the work to protect the laser diode including the continuous adjustable output power with high accuracy and stability is easily obtained. The internal-external modulation control of the laser power based on digital optical feedback can be accomplished with stable power output. At last the bringing reasons of noise are analyzed and the solving methods are put forward in this paper.