机构

• 长春光学精密机械与物... [3]
• 力学研究所 [1]

采集方式

• OAI收割 [4]

内容类型

• 会议论文 [3]
• 期刊论文 [1]

发表日期

• 2021 [1]
• 2012 [2]
• 2005 [1]

学科主题

• Environmen... [1]
• Marine & F... [1]

筛选

浏览/检索结果: 共4条，第1-4条 帮助 条数/页： 5101520253035404550556065707580859095100 排序方式： 请选择题名升序题名降序提交时间升序提交时间降序作者升序作者降序发表日期升序发表日期降序 Hydrodynamic Performance of an Asymmetry OWC Device Mounted on a Box-Type Breakwater 期刊论文  OAI收割 FRONTIERS IN MARINE SCIENCE, 2021, 卷号: 8, 页码: 677030 作者:  Deng, Zhengzhi;  Wang, Pinjie;  Cheng PD(程鹏达)   |  收藏  |  浏览/下载：31/0  |  提交时间：2022/10/25 wave energy conversion  oscillating water column  hydrodynamics  experimental and numerical study  energy dissipation   Deep subwavelength electromagnetic transparence through dual metallic gratings with ultranarrow slits (EI CONFERENCE) 会议论文  OAI收割 2012 International Workshop on Metamaterials, Meta 2012, October 8, 2012 - October 10, 2012, Nanjing, China 作者:  Liu Z.;  Li S.;  Li F. 收藏  |  浏览/下载：28/0  |  提交时间：2013/03/25 We study the transmission response of microwaves through two identical metallic plates perforated with periodical ultranarrow slits. The experimental and numerical transmission spectra consistently display a striking transmission peak at wavelength much larger than any characteristic length of the microstructure (e.g.  about 20-fold of the lattice constant)  which can not be directly interpreted by the existing mechanisms. Both the LC-circuit-based microscopic picture and the effective-medium-based macroscopic model are established to capture the essential physics behind such unexpected resonance at the deep subwavelength scale. 2012 IEEE.   Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文  OAI收割 2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China Zi K.; Chen L. 收藏  |  浏览/下载：20/0  |  提交时间：2013/03/25 With finite element analysis software Moldflow  numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot  gas pressure  delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index  the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding  optimum pre-injection shot is 94%  gas pressure is 15MPa  delay time is 0.5s  melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.   Numerical analysis and experimental research of output performance for Yb3+-doped double-clad fiber lasers (EI CONFERENCE) 会议论文  OAI收割 High-Power Lasers and Applications III, November 8, 2004 - November 11, 2004, Beijing, China 作者:  Wang G.;  Gao Y.;  Li Y.;  Li Y.;  Li Y. 收藏  |  浏览/下载：16/0  |  提交时间：2013/03/25 In this paper  numerical analysis was investigated for the double-clad fiber lasers and experimental study on the Yb3+-doped double-clad fiber lasers was performed. The results shown that the output power increased monotonically with absorbed power  and in lossy cavity the output power is less than in the lossless cavity. The output power decreases for the lossy fiber with the reflectivity of output coupler. There was an optimum fiber length to reach a maximum output and the optimum length was mainly dependent on the loss coefficient. In experiment we obtained a output power of 21.6W  slope efficiency of 54% by using Yb3+-doped double-clad fiber and 40W LD pump source.