机构

• 武汉岩土力学研究所 [2]
• 长春光学精密机械与物... [1]
• 广州能源研究所 [1]
• 近代物理研究所 [1]
• 工程热物理研究所 [1]

采集方式

• OAI收割 [6]

内容类型

• 期刊论文 [5]
• 会议论文 [1]

发表日期

• 2024 [1]
• 2022 [1]
• 2020 [1]
• 2017 [1]
• 2016 [1]
• 2012 [1]
• 更多

学科主题

• Energy & F... [1]

筛选

浏览/检索结果: 共6条，第1-6条 帮助 条数/页： 5101520253035404550556065707580859095100 排序方式： 请选择题名升序题名降序发表日期升序发表日期降序提交时间升序提交时间降序作者升序作者降序 Leakage Risk Analysis of Underground Gas Storage Salt Caverns with Micro-leakage Interlayer in Bedded Rock Salt of Jiangsu, China 期刊论文  OAI收割 ROCK MECHANICS AND ROCK ENGINEERING, 2024, 页码: 17 作者:  Yin, Hongwu;  Ma, Hongling;  Shi, Xilin;  Ge, Xinbo   |  收藏  |  浏览/下载：2/0  |  提交时间：2025/06/27 Underground gas storage (UGS) salt caverns  Micro-leakage interlayer  Tightness  Seepage distance  Injection-production method  Gas leakage rate   Detection and Evaluation Technologies for Using Existing Salt Caverns to Build Energy Storage 期刊论文  OAI收割 ENERGIES, 2022, 卷号: 15, 期号: 23 作者:  Liu, Yuanxi;  Li, Yinping;  Ma, Hongling;  Shi, Xilin;  Zheng, Zhuyan   |  收藏  |  浏览/下载：14/0  |  提交时间：2023/08/02 energy storage  existing salt cavern  natural gas storage  compressed air energy storage  brine injection method  tightness   The influence of the water injection method on two-well-horizontal salt cavern construction 期刊论文  OAI收割 JOURNAL OF PETROLEUM SCIENCE AND ENGINEERING, 2020, 卷号: 184, 页码: 11 作者:  Wan, Jifang;  Peng, Tianji;  Jose Jurado, Maria;  Shen, Ruichen;  Yuan, Guangjie   |  收藏  |  浏览/下载：21/0  |  提交时间：2022/01/19 Compressed natural gas  Salt cavern  Two-well-horizontal  Water injection method  Injection direction  Flow rate   甲烷气体注入方式对甲烷水合物生成的影响 期刊论文  OAI收割 新能源进展, 2017, 卷号: 5, 期号: 4, 页码: 300-304 作者:  丁亚龙;  徐纯刚;  李小森   |  收藏  |  浏览/下载：29/0  |  提交时间：2018/12/21 甲烷水合物  I型水合物  进气方式  methane hydrate  structure I hydrate  gas injection method   Numerical Prediction of Film Cooling Effectiveness over Flat Plate using Variable Turbulent Prandtl Number Closures 期刊论文  OAI收割 2016 作者:  Ochrymiuk, T. 收藏  |  浏览/下载：30/0  |  提交时间：2017/05/27 turbulent heat flux two-equation model turbulent Prandtl number film cooling compound-angle injection crystal image method gas-turbine blade   Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文  OAI收割 2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China Zi K.; Chen L. 收藏  |  浏览/下载：24/0  |  提交时间：2013/03/25 With finite element analysis software Moldflow  numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot  gas pressure  delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index  the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding  optimum pre-injection shot is 94%  gas pressure is 15MPa  delay time is 0.5s  melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.