中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共5条，第1-5条

帮助

条数/页：排序方式：
	Design and Analysis of High Temperature Superconducting Current Leads for CRAFT TF Magnet 期刊论文 OAI收割 IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY, 2023, 卷号: 33 作者: Han, Quan; Lu, Kun; Song, Yuntao; Ding, Kaizhong; Liu, Chen \| 收藏 \| 浏览/下载：75/0 \| 提交时间：2023/11/10 Analysis Comprehensive Research Facility for Fusion Technology (CRAFT) high-temperature superconducting current leads (HTSCL) structure design toroidal field (TF) magnet
	Study on heat transfer and fluidity of three-dimensional invisible finned-tube 期刊论文 OAI收割 JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY, 2020, 页码: 12 作者: Mo, X.; Zhu, D. S.; Wang, F. Y.; Yin, Y. D. \| 收藏 \| 浏览/下载：22/0 \| 提交时间：2020/10/30 Enhanced tube Heat transfer Convection Design Three-dimensional invisible finned-tube Comprehensive performance evaluation factor
	An sequential optimization and aeroelastic constraint transformation method for strength-aeroelastic comprehensive design 期刊论文 OAI收割 JOURNAL OF FLUIDS AND STRUCTURES, 2020, 卷号: 93, 页码: 14 作者: Zhang ZS; Wang XJ; Chen XJ(陈贤佳); Chen XJ(陈贤佳) \| 收藏 \| 浏览/下载：53/0 \| 提交时间：2020/04/07 Comprehensive design Sequential optimization strategy Airplane wing Structural strength Aeroelasticity
	LABTM control system based on FPGA (EI CONFERENCE) 会议论文 OAI收割 2nd International Conference on Mechatronics and Applied Mechanics, ICMAM 2012, December 8, 2012 - December 9, 2012, Taiwan 作者: Wang Y.; Yu P.; Yu P.; Wang Y.; Wang Y. 收藏 \| 浏览/下载：160/0 \| 提交时间：2013/03/25 This paper presents the digital PI control method for design and simulation of a high precision limited angle brushless torque motor control system in Field Programmable Gate Array device (FPGA). The direct drive structures which are widely applied in many servo control fields. Matlab Xilinx System GeneratorR toolbox based on Fixed-Point Arithmetic is used to design the digital PI controller using DSP architecture plot the responses of the control system and generate the VHDL source code. The control system model consists of a digital PI a real LABTM and a real absolute Inductosyn encoder to rpm and position blocks. Through loading generated codes in process of the simulation that built by the digital discrete model it is verified that the rising time of current loop is only 1.2ms and rate loop is 8ms overshoot is rarely 4.2%. Finally the comprehensive positioning accuracy of system can reach up to 5 arc sec and the rate jitter achieves 5% with the 4 arc sec accuracy absolute Inductosyn. (2013) Trans Tech Publications Switzerland.
	Evaluation of the operating range for ground-based infrared imaging tracking system (EI CONFERENCE) 会议论文 OAI收割 International Symposium on Photoelectronic Detection and Imaging 2011: Advances in Infrared Imaging and Applications, May 24, 2011 - May 24, 2011, Beijing, China 作者: Zhang Z.-D. 收藏 \| 浏览/下载：51/0 \| 提交时间：2013/03/25 Ground-based infrared imaging tracking system (GIITS) is of great importance for aerial target warning and guard. The operating range is one of the key performance specifications on the other which should be calculated calculate the radiation power received on the detector in order to analysis whether the output signal meets the detection requirements or not analyzed and studied during the whole GIITS design process. The operating range is mostly influenced by a few factors without considering the effect of the background radiation. By improving of the traditional method including atmospheric attenuation a new operating range calculation model of the GIITS was established based on two requirements. One is that the image size of observed target should meet the requirement of the processor signal extraction. The number of the pixel occupied by target image should be more than 9. The other is that the signal noise ratio (SNR) of the GIITS should not be less than 5 to meet the requirements of the target detection probability and spatial frequency. The SNR calculation equation in form of energy is deduced and the radiation characteristic of the observed target and background are analyzed. When evaluate the operating range of the GIITS using the new method the performance of GIITS and feature of target and background. This paper firstly makes analysis and summarization on the definite localizations of the traditional operating range equation of the GIITS. The localizations are mainly in two aspects. On one hand we should successively calculate two operating range values according to two requirements mentioned above and choose the minimum value as the analytic result. In the end the dispersion of the image and the effect of image dispersion are not considered in the traditional method an evaluation of operating range for fighter aircraft is accomplished as an example. The influence factors in every aspect on operating range were explored by the calculated result. The new operating range calculation model provides the theoretical basis for the design and applications as well as the comprehensive evaluation of a GIITS. 2011 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).