中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共8条，第1-8条

帮助

条数/页：排序方式：
	LCVR-based Stokes polarimeter: Principles and evaluation 会议论文 OAI收割 Sydney, NSW, Australia, 2023-06-01 作者: Chang, Lingying; Wang, Guanru; Wang, Xinyou; Qiu, Yuehong; Chen, Kui \| 收藏 \| 浏览/下载：16/0 \| 提交时间：2023/12/26 Stokes polarimeter LCVR Measurement matrix Evaluation parameters
	The structural diversity of ibuprofen sustained-release pellets on the same goal of bioequivalence consistency 期刊论文 OAI收割 MATERIALS & DESIGN, 2022, 卷号: 217, 页码: 11 作者: Cao, Zeying; Sun, Ningyun; Sun, Hongyu; Liu, Jun; Li, Jing \| 收藏 \| 浏览/下载：20/0 \| 提交时间：2023/04/10 Consistency evaluation Bioequivalence Three-dimensional structures Internal structure parameters Ibuprofen sustained-release pellets Micro-computed tomography
	An Evaluation Method of Brittleness Characteristics of Shale Based on the Unloading Experiment 期刊论文 OAI收割 ENERGIES, 2019, 卷号: 12, 期号: 9, 页码: - 作者: Zhou, Xiaogui; Liu, Haiming; Guo, Yintong; Wang, Lei; Hou, Zhenkun \| 收藏 \| 浏览/下载：22/0 \| 提交时间：2020/04/08 shale unloading rate brittleness evaluation failure characteristics mechanical parameters
	Performance Evaluation and Improvement of Chipset Assembly & Test Production Line Based on Variability 期刊论文 OAI收割 International Journal of Automation and Computing, 2019, 卷号: 16, 期号: 2, 页码: 186-198 作者: Chang-Jun Li; Zong-Shi Xie; Xin-Ran Peng; Bo Li \| 收藏 \| 浏览/下载：11/0 \| 提交时间：2021/02/22 Performance evaluation and improvement chipset assembly & test production line (CATPL) parameters Little′s law variability.
	Two types of phase diagrams for two-species Bose-Einstein condensates and the combined effect of the parameters 期刊论文 OAI收割 JOURNAL OF PHYSICS B-ATOMIC MOLECULAR AND OPTICAL PHYSICS, 2017, 卷号: 50, 期号: 13, 页码: 135301 作者: Bao, CG; Li, ZB; Liu, YM; Yao, DX; Bao, CG (reprint author), Sun Yat Sen Univ, Sch Phys, State Key Lab Optoelect Mat & Technol, Guangzhou 510275, Guangdong, Peoples R China. \| 收藏 \| 浏览/下载：29/0 \| 提交时间：2017/12/21 Two-species Bose-einstein Condensate Phase Diagrams For Two-species Condensates CombIned Effect Of The Parameters In Bec Evaluation Of The Parameters In Bec
	Tracking error modeling of the theodolite based on GRNN method (EI CONFERENCE) 会议论文 OAI收割 2nd International Conference on Frontiers of Manufacturing and Design Science, ICFMD 2011, December 11, 2011 - December 13, 2011, Taichung, Taiwan 作者: Li M. 收藏 \| 浏览/下载：23/0 \| 提交时间：2013/03/25 To meet the requirement of high tracking accuracy as well as develop more reasonable evaluation method in this paper the General Regression Neural Network (GRNN) has been applied to build the tracking error model of the theodolite. First we analyze the nonlinear factors in the theodolite. Second we discuss the principle of GRNN including its structure the function as well as its priors. Third we build the tracking error model based on GRNN and verify the model through the different parameters. The result indicated that the network model based on GRNN has high accuracy and good generalization ability. It could instead the real system to a certain extent. The research in this paper has important value to the engineering practice.
	Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文 OAI收割 2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China Zi K.; Chen L. 收藏 \| 浏览/下载：20/0 \| 提交时间：2013/03/25 With finite element analysis software Moldflow numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot gas pressure delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding optimum pre-injection shot is 94% gas pressure is 15MPa delay time is 0.5s melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.
	Studies of transverse phase space painting for the CSNS RCS injection 期刊论文 OAI收割 HIGH ENERGY PHYSICS AND NUCLEAR PHYSICS-CHINESE EDITION, 2007, 卷号: 31, 期号: 10, 页码: 942-946 作者: Qiu J(邱静); Tang JY(唐靖宇); Wang S(王生); Wei J(韦杰); Qiu, J 收藏 \| 浏览/下载：21/0 \| 提交时间：2016/06/29 H- stripping injection phase space painting space-charge effects uniformity evaluation parameters