中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共5条，第1-5条

帮助

条数/页：排序方式：
	Design and Thermal Stability Analysis of Swing Micro-Mirror Structure for Gravitational Wave Observatory in Space 期刊论文 OAI收割 machines, 2021, 卷号: 9, 期号: 5, 页码: 104-127 作者: Zheng KY(郑焜耀); Xu MM(许明明) \| 收藏 \| 浏览/下载：61/0 \| 提交时间：2022/04/01 swing micro-mirror structure finite element analysis amplitude spectral density point- ing jitter first-order natural frequency
	Structural design of primary mirror subassembly for space telescope (EI CONFERENCE) 会议论文 OAI收割 2nd International Conference on Mechatronics and Applied Mechanics, ICMAM 2012, December 8, 2012 - December 9, 2012, Taiwan 作者: Xu H. 收藏 \| 浏览/下载：60/0 \| 提交时间：2013/03/25 In order to design a large aperture primary mirror with the diameter of 1150 mm the parameters impacting on gravity deformation of the mirror were analyzed and discussed in detail including material selection diameter-thickness ratio the number of the support points location selection and lightweight structure etc. A novel space mirror structure system was put forward and its back was opened and supported by six points on back. The dynamic and static and thermal characteristics were analyzed based on the finite element method. Analysis results showed the surface figure accuracy reached to RMS 14.5nm under the action of gravity load along the optical axis direction and the first-order natural frequency was 214Hz which met to the designed indexes requirements. (2013) Trans Tech Publications Switzerland.
	Structural design of large aperture rectangular mirror for space telescope (EI CONFERENCE) 会议论文 OAI收割 2nd International Conference on Civil Engineering and Transportation, ICCET 2012, October 27, 2012 - October 28, 2012, Guilin, China 作者: Li Z.; Li Z. 收藏 \| 浏览/下载：40/0 \| 提交时间：2013/03/25 Structural design of large aperture mirror is one of the key technologies for space telescope development. To meet the requirements of high stiffness strength and thermal dimensional stability some factors such as support scheme materials selection lightweight design and flexible support design were taken into account. The three supports location of the mirror was determined according to the modal analytical solution. By adjusting the parameters of flexure hinge influences of gravity assembly stress and thermal stress on the mirror were reduced obviously. Finite element analysis (FEA) results indicate that the surface accuracy reach to rms10.2nm and 10.8nm under the gravity along optical axis direction and 5C uniform temperature rise respectively the fundamental frequency of the mirror component is 268Hz. Dynamics test shows that the first order natural frequency is 256Hz which shows an error less than 5% compared to FEA results. (2013) Trans Tech Publications Switzerland.
	Lightweight design of large scale theodolite's turntable based on topology optimization of continuum structure (EI CONFERENCE) 会议论文 OAI收割 2012 International Conference on Optoelectronics and Microelectronics, ICOM 2012, August 23, 2012 - August 25, 2012, Changchun, China 作者: Wang Y.; Wang Y.; Wang Y.; Wang Y.; Wang Y. 收藏 \| 浏览/下载：27/0 \| 提交时间：2013/03/25 In order to solve the problem that the weight of large scale theodolite's casting or steel plate welded structure is too heavy lightweight design of large scale turntable based on topology optimization of continuum structure is investigated. Topology optimization could have better optimization efficiency because it can provide the optimized distribution of material and gain optimized structure in conceptual design phase of the structural design. In order to obtain lightweight and high stiffness structure a truss turntable based on topology optimization of continuum structure is presented and the validity of this lightweight structure is examined by finite element analysis. Comparing to the traditional welding steel turntable the lightweight turntable without changing the static displacement can lose 386.48 kg(lightweight ratio is 26.7%) and its first-order natural frequency raises from 167.02Hz to 173.71Hz. Meanwhile in other aspects this turntable also has better performance than traditional structure. 2012 IEEE.
	The effect of backlash nonlinear on resonance frequency of electric actuator transmission system (EI CONFERENCE) 会议论文 OAI收割 3rd IEEE International Conference on Advanced Computer Control, ICACC 2011, January 18, 2011 - January 20, 2011, Harbin, China Han X.; Ge M.; Bai Y.; Jia H.; Ge W. 收藏 \| 浏览/下载：20/0 \| 提交时间：2013/03/25 In order to study the effect of backlash nonlinear on resonance frequency of electric actuator transmission system then Finally in the premise of meeting the stability the dynamic equilibrium equation of transmission system with backlash is established it makes dynamic simulation analysis for the transmission system based on virtual prototype technology it establishes balanced equation of dynamics system with backlash the effect of backlash on system natural frequency and resonance frequency and the theoretical values and simulation values are compared. Theoretical analysis and simulation results show that the theoretical analysis is basically consistent with simulation results when it is zero backlash and does some theory research and dynamic analysis of backlash nonlinearity and system natural frequency and resonance frequency. First and the error of theoretical analysis and simulation results is within 10%. Therefore according to describing function to theoretically model the backlash nonlinear it can be concluded that considering the transmission system theoretical analysis of backlash nonlinearity is feasible the relation between describing function and the amount of backlash and input amplitude is analyzed and it is much closer to the actual system with instructive significance. 2011 IEEE.