中国科学院机构知识库网格
Chinese Academy of Sciences Institutional Repositories Grid
机构
采集方式
内容类型
发表日期
学科主题
筛选

浏览/检索结果: 共16条,第1-10条 帮助

条数/页: 排序方式:
The ultra-high sensitivity of mass resonator achieved by the beam with variable thickness 期刊论文  OAI收割
RESULTS IN PHYSICS, 2023, 卷号: 49, 页码: 106483
作者:  
Wei CX(卫晨曦);  Zhang Y(张吟)
  |  收藏  |  浏览/下载:17/0  |  提交时间:2023/06/15
Experimental Study on the Influence of Flexible Control on Key Parameters in Reverse Osmosis Desalination 期刊论文  OAI收割
IEEE ACCESS, 2022, 卷号: 10, 页码: 4844-4860
作者:  
Chu, Shuai;  Zhang, Shitan;  Ma, Xiaona;  Li, Yinxuan;  Qiu, Denggao
  |  收藏  |  浏览/下载:40/0  |  提交时间:2022/02/21
Energy Efficient Control of Parallel Variable-Frequency Pumps in Magnetic Water-Cooling System 期刊论文  OAI收割
JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME, 2020, 卷号: 142
作者:  
Qiu, Wenjun;  Ouyang, Zhengrong
  |  收藏  |  浏览/下载:91/0  |  提交时间:2020/11/26
Comparative study of receiver-side ghost wavefield attenuation on different marine acquisition configurations 期刊论文  OAI收割
Journal of Geophysics and Engineering, 2018, 卷号: 15, 期号: 2
作者:  
Zhang,Hao;  Liu,Qiancheng;  Li,Hongyuan;  Zhang,Yi
  |  收藏  |  浏览/下载:38/0  |  提交时间:2018/09/26
Doppler-robust high-spectrum-efficiency VCM-OFDM scheme for low Earth orbit satellites broadband data transmission 期刊论文  OAI收割
IET COMMUNICATIONS, 2018, 卷号: 12, 期号: 1, 页码: 35-43
作者:  
Li, Jionghui;  Xiong, Weiming;  Sun, Geng;  Wang, Zhugang;  Huang, Yonghui
  |  收藏  |  浏览/下载:73/0  |  提交时间:2018/03/02
Multi-target detection method based on variable carrier frequency chirp sequence 期刊论文  OAI收割
SENSORS, 2018, 卷号: 18, 期号: 10, 页码: 1-12
作者:  
Wang W(王伟);  Du JS(杜劲松);  Gao J(高洁)
  |  收藏  |  浏览/下载:68/0  |  提交时间:2018/11/09
单缸补气转子式压缩机在热泵系统中制热性能 期刊论文  OAI收割
化工学报, 2017, 卷号: 68, 期号: 9, 页码: 3551-3557
作者:  
孙晋飞;  朱冬生;  尹应德;  李修真;  涂爱民
  |  收藏  |  浏览/下载:33/0  |  提交时间:2018/12/21
变频双级离心式冷水机组原理及其控制分析 期刊论文  OAI收割
流体机械, 2017, 卷号: 45, 期号: 6, 页码: 77-82
作者:  
董凯军;  邵振华;  王志强;  孙钦;  黄祥发
  |  收藏  |  浏览/下载:31/0  |  提交时间:2018/12/21
Laser cleaning of neutral attenuator plate based on low power laser diode (EI CONFERENCE) 会议论文  OAI收割
2nd International Conference on Energy, Environment and Sustainable Development, EESD 2012, October 12, 2012 - October 14, 2012, Jilin, China
作者:  
Chen Y.;  Li L.
收藏  |  浏览/下载:30/0  |  提交时间:2013/03/25
Laser cleaning is a non-contact  green and environmental cleaning method  which can effectively remove particulate contaminations of sizes as small as 0.1 m without damage to the optics. But most laser cleaning devices are large and heavy  also expensive due to using large lasers such as CO2 laser  YAG Laser etc. In this work a low power LD was tried to clean fingerprint and dust contaminated on the surface of the attenuator glasses plates. In the laser cleaning experiment with low power diode the fingerprint grease can be efficient to be cleaned  but there is no evident effect for cleaning inorganic dust. The cleaning different degree of fingerprint contaminations was investigated at the variable laser parameters  including laser power and irradiation time. An optical microscope was used to analyze the cleaning effect. The results show that low power LD can effectively remove the fingerprint on the surface of absorptive-type attenuator glass plates. On the premise that the attenuator optics glasses are not damaged  the cleaning area increases with the increase of radiation time and laser power. The cleaning area doesn't change much with the variation of laser frequency when the other parameters are the same. (2013) Trans Tech Publications  Switzerland.  
Design and optimization of supporting structure for scanning mirror in aviation remote sensor (EI CONFERENCE) 会议论文  OAI收割
2011 International Conference on Electric Information and Control Engineering, ICEICE 2011, April 15, 2011 - April 17, 2011, Wuhan, China
作者:  
Yang H.
收藏  |  浏览/下载:28/0  |  提交时间:2013/03/25
An optical supporting structure is studied to improve its structure stiffness and reduce the rotate error to meet the requirement of aviation remote sensor. A formula to calculate fundamental frequency is proposed using Rayleigh-Ritz method  and a method of is analyzed. By means of OPTISTRUCT software  the maximum fundamental frequency is converted to object function  the deformation under the gravity and the mass are assigned to state variable  wall thicknesses of the structure are converted to design variables. The analysis and test results indicate that the fundamental frequency of designed optical supporting structure has been improved 37.2 Hz from 96.9 Hz  which guarantee the reliability of the sweep mechanism  and the rotate error is 4.89  which is satisfied for the rotate accuracy in plunge angle. The method of optimization has a certain instructional significance for the design of supporting structures in aviation remote sensor. 2011 IEEE.