中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共9条，第1-9条

帮助

条数/页：排序方式：
	Research on load-bearing characteristics of precision air-bearing rotary stage (EI CONFERENCE) 会议论文 OAI收割 3rd international Conference on Manufacturing Science and Engineering, ICMSE 2012, March 27, 2012 - March 29, 2012, Xiamen, China 作者: Wang L.; Wang L.; Wang L.; Lin J. 收藏 \| 浏览/下载：117/0 \| 提交时间：2013/03/25 Air-bearing is a core component of air-bearing rotary stage. The weakness that the air-bearing has the low load capacity and stiffness has been concerned about by domestic and foreign scholars. So how to improve the load capacity and stiffness has become a serious problem. In order to improve the load capacity and stiffness of the air-bearing rotary stage in this paper we improved structure of Zhang Wenjie and others' high-precision direct-drive air-bearing rotary stage. The gas film of air-bearing has been meshed by GAMBIT software and we use FLUENT software to obtain the carrying capacity features of the gas film. Finally the structural static force of the precision air-bearing rotary stage will be analyzed by ANSYS software. The analysis results show that: the structural design of the precision air-bearing rotary stage is reasonable and this structure can provide a larger range of loads. Even in heavy load conditions a larger deformation will not occur any more. It has a good practical value and also can be widely used in high precision equipments. (2012) Trans Tech Publications.
	A method combining numerical analysis and limit equilibrium theory to determine potential slip surfaces in soil slopes 期刊论文 OAI收割 JOURNAL OF MOUNTAIN SCIENCE, 2011, 卷号: 8, 期号: 5, 页码: 718–727 Xiao Shiguo; Yan Liping; Cheng Zhiqiang 收藏 \| 浏览/下载：27/0 \| 提交时间：2013/08/12 Soil slope Stress field Potential slip surface Slope stability Factor of safety Numerical analysis Limit equilibrium method ANSYS software
	Surface shape optimization for the space membrane reflector (EI CONFERENCE) 会议论文 OAI收割 2011 International Conference on Electronic and Mechanical Engineering and Information Technology, EMEIT 2011, August 12, 2011 - August 14, 2011, Harbin, China 作者: Zhang Y.; Zhang P. 收藏 \| 浏览/下载：23/0 \| 提交时间：2013/03/25 Space membrane reflector is very promised for optical quality application with the merits of ultra-lightweight and flexible. In order to improve the surface precision of membrane reflectors the formation and surface shape error of a membrane at uniform load are studied based on the henky-cambell equations of circular membrane. The ANSYS software is used to build an optimization model of membrane reflector surface shape in which the yield strength is the state variable the surface load on ten concentric annular regions of the mirror is the design variable and the minimum RMS between ideal surface and mirror surface is the target function. and the theoretical and experimental result show that RMS and PV of the optimized surfaces are reduced respectively than those before optimization. In a word this paper offers the theoretical and experimental basis of the polyimide membrane reflector. 2011 IEEE.
	Thermal analysis on supersonic ellipsoidal dome (EI CONFERENCE) 会议论文 OAI收割 2nd International Conference on Multimedia Technology, ICMT 2011, July 26, 2011 - July 28, 2011, Hangzhou, China Jiang Z.; Wei Q.; Jia H. 收藏 \| 浏览/下载：32/0 \| 提交时间：2013/03/25 Studied the transient thermal transfer analysis method due to a kind of supersonic ellipsoidal dome which is a conformal dome. Illuminated the principle of transient thermal transfer analysis. Accomplished the transient thermal analysis based on the model of ellipsoidal dome and studied the influence about the different material and the different velocity. Considered three materials consist of MgF2 Al2O3 and ZnS and meanwhile the velocity was Mach2.5 and the time consists of 10s 20s and 60s. The temperature initial loads were from FLUENT thermal simulation. The thermal conduction analysis and the thermal convection analysis were finished in software ANSYS in which the entire transient thermal analysis consists of modeling meshing element calculating and getting the results. The different temperature distributions based on varied time were gotten about the different materials. The results from analysis showed the temperature distribution of the structure of ellipsoidal dome which could help the following coupled thermal-structure analysis. 2011 IEEE.
	Dynamic optimum design and analysis of cam wave generator for harmonic gear drive (EI CONFERENCE) 会议论文 OAI收割 2011 International Conference on Information and Automation, ICIA 2011, June 6, 2011 - June 8, 2011, Shenzhen, China Xiao Q.; Han X.; Jia H. 收藏 \| 浏览/下载：27/0 \| 提交时间：2013/03/25 Mathematical models of structural optimization were established for the cam wave generator then a conceptual model by integrally taking its static and dynamic performance into consideration which satisfied the model acted by four concentrated forces while the dynamic optimum design was carried out. The topology optimization of the cam wave generator was performed based on artificial material density method was obtained. And the size optimization of the cam wave generator was also executed based on the zero-order method in software Ansys after setting up its parameterized model. The optimized results indicate that its final volume declines to 1284.217mm3 from its 1397.830mm3 which reduced by 42.18% than the original volume of cam (2221.224mm3). Simultaneously the static analysis and modal analysis were implemented and the results show that the static and dynamic performance complies with the design requirements proving that the results of dynamic optimum design are reasonable. The optimized results in paper are realizable in engineering. And the study method provides not only a reference to decreasing design mass and lowering inertia of the cam wave generator but also an important basis of lightweight design of harmonic gear drive. 2011 IEEE.
	Optimal design of strap-down inertial navigation support under random loads (EI CONFERENCE) 会议论文 OAI收割 2010 IEEE International Conference on Information and Automation, ICIA 2010, June 20, 2010 - June 23, 2010, Harbin, Heilongjiang, China 作者: Li M. 收藏 \| 浏览/下载：29/0 \| 提交时间：2013/03/25 In order to realize miniaturization and light weight of the strap-down inertial navigation system and then to make sure that it works well under random loads optimal design is applied to the strap-down inertial navigation support with the methods of topology optimization and size optimization. Firstly based on the installation requirement of devices and connection requirement of the support and the carrier the initial structure of the support is designed. Topology optimization with FEA software ANSYS is adopted on the initial structure to get the basic one. Then 5 critical sizes are chosen as design variables and the support structure is optimized by means of size optimization to reach light weight with satisfying the requirement of dynamic stiffness. Finally random vibration analysis is applied to the initial structure. In the mean time random vibration test is carried out to qualify the analysis method. After the qualification a random vibration analysis is applied to the optimized support structure to get the rms of displacement response and acceleration response of the support to validate whether the optimized structure is appropriate. The results indicate that the dynamic stiffness of the optimized support structure satisfies the design requirements and its weight is lighter 49.38% than that of the initial one. This research can be a reference to the structure design of supports under random loads and the result has been applied to the development and manufacture of a prototype aerocraft. 2010 IEEE.
	Material properties test and numerical simulation of impact for die cast magnesium alloy (EI CONFERENCE) 会议论文 OAI收割 International Conference on Magnesium - Science, Technology and Applications, September 20, 2004 - September 24, 2004, Beijing, China Zeng X.; Wu Q.; Liyuan; Fan J. 收藏 \| 浏览/下载：65/0 \| 提交时间：2013/03/25 The poison's ratio of plane plate samples taken from AM60 magnesium alloy was tested in this paper. A number of strain controlled fatigue experiments were also carried out on MTS to investigate the stress-strain behavior under different temperature conditions. The finite element analysis software ANSYS was employed to simulate impact process of shot blasting. Results indicated that at the specific temperature condition the residual stress and plastic strain increased with impact velocity increasing. At the specific impact velocity residual stress reduced and plastic strain increased with temperature increment.
	Two-dimensional numerical modeling research on continent subduction dynamics 期刊论文 OAI收割 ACTA GEOLOGICA SINICA-ENGLISH EDITION, 2004, 卷号: 78, 期号: 1, 页码: 313-319 作者: Wang, ZM; Bei, X; Zhou, YQ \| 收藏 \| 浏览/下载：20/0 \| 提交时间：2018/09/26 continent subduction application of ANSYS software dynamic mechanism modeling plate tectonics
	Two-dimensional numerical modeling research on continent subduction dynamics 期刊论文 OAI收割 ACTA GEOLOGICA SINICA-ENGLISH EDITION, 2004, 卷号: 78, 期号: 1, 页码: 313-319 作者: Wang, ZM; Bei, X; Zhou, YQ; Xu, HH; Huang, SY \| 收藏 \| 浏览/下载：10/0 \| 提交时间：2018/09/26 continent subduction application of ANSYS software dynamic mechanism modeling plate tectonics