中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共6条，第1-6条

帮助

条数/页：排序方式：
	Performance Evaluation and Improvement of Chipset Assembly & Test Production Line Based on Variability 期刊论文 OAI收割 International Journal of Automation and Computing, 2019, 卷号: 16, 期号: 2, 页码: 186-198 作者: Chang-Jun Li; Zong-Shi Xie; Xin-Ran Peng; Bo Li \| 收藏 \| 浏览/下载：14/0 \| 提交时间：2021/02/22 Performance evaluation and improvement chipset assembly & test production line (CATPL) parameters Little′s law variability.
	Structural design of large aperture rectangular mirror for space telescope (EI CONFERENCE) 会议论文 OAI收割 2nd International Conference on Civil Engineering and Transportation, ICCET 2012, October 27, 2012 - October 28, 2012, Guilin, China 作者: Li Z.; Li Z. 收藏 \| 浏览/下载：43/0 \| 提交时间：2013/03/25 Structural design of large aperture mirror is one of the key technologies for space telescope development. To meet the requirements of high stiffness strength and thermal dimensional stability some factors such as support scheme materials selection lightweight design and flexible support design were taken into account. The three supports location of the mirror was determined according to the modal analytical solution. By adjusting the parameters of flexure hinge influences of gravity assembly stress and thermal stress on the mirror were reduced obviously. Finite element analysis (FEA) results indicate that the surface accuracy reach to rms10.2nm and 10.8nm under the gravity along optical axis direction and 5C uniform temperature rise respectively the fundamental frequency of the mirror component is 268Hz. Dynamics test shows that the first order natural frequency is 256Hz which shows an error less than 5% compared to FEA results. (2013) Trans Tech Publications Switzerland.
	The flow field analysis of the automotive power streering congtrol unit's flow channel (EI CONFERENCE) 会议论文 OAI收割 2011 International Conference on Advanced Design and Manufacturing Engineering, ADME 2011, September 16, 2011 - September 18, 2011, Guangzhou, China Cheng K.; Yan L.; Li G.; Tang J. 收藏 \| 浏览/下载：16/0 \| 提交时间：2013/03/25 The automotive power steering units must be taken performance test after they are integrated assembly and then left the factory if it is qualified.Because its internal flow channel is very complicated and the residual hydraulic oil can not be eleminated clearly.So we can set up a 3D model flow channel based on CATIA and use FLUENT software to analysis the key flow channel analysing it's pressure distribution and velocity vector diagram then get the real reasonable resluts which can provide the basic for the ejector designing. (2011) Trans Tech Publications.
	Nonlinear analysis method for predicting optical surface deformations resulted from assembly process (EI CONFERENCE) 会议论文 OAI收割 5th International Symposium on Advanced Optical Manufacturing and Testing Technologies: Large Mirrors and Telescopes, April 26, 2010 - April 29, 2010, Dalian, China Dong W.; Yong Y.; Guang J. 收藏 \| 浏览/下载：25/0 \| 提交时间：2013/03/25 There are three main nonlinear elements in the large mirror assemblies which are screw pretension adhesive stress and state changes in the assembly process. The optical shape will be influenced seriously by these factors. But the impacts will not be shown in linear analysis results because as the simplification these factors have been ignored. The nonlinear analysis method for predicting optical surface deformations resulted from assembly process is discussed in detail. Take a typical mirror support structure for example the nonlinear analysis model was established. Comparing the calculation results with the optical shape test it is illustrated that nonlinear analysis is more accurate and closer to the test result. And according to the simulation result the bowl-shaped depression which was discovered in the test can also be explained reasonably. 2010 Copyright SPIE - The International Society for Optical Engineering.
	Design of optical lens for space tridimensional mapping camera (EI CONFERENCE) 会议论文 OAI收割 4th International Symposium on Advanced Optical Manufacturing and Testing Technologies: Advanced Optical Manufacturing Technologies, November 19, 2008 - November 21, 2008, Chengdu, China 作者: Wang Z.; Wang Z.; Zhang L.-P. 收藏 \| 浏览/下载：26/0 \| 提交时间：2013/03/25 Three-linear array tridimensional mapping camera consists of three independent linear CCD cameras. Unique position must be kept among the three linear CCD cameras. Optical lens is one of pivotal parts MTF the ground resolution power is 5m resolving power the distortion is 3/10000. They meet the need of user. 2009 SPIE. distortion are its important techno-items. The optical lens of space tridimensional mapping camera is the key to accomplish the tridimensional mapping mission. In order to meet the need of user a design on optical lens of transmission semi-telecentric beam path in image space is expounded and assembly method based on DFT(Design For Test) of single lens suit and whole optical lens are expounded. The test results indicates that the MTF of optical lens referred in the paper is 0.45(@77lp/mm)
	A unique truss for large segmented-mirror telescope 会议论文 OAI收割 Orlando, FL, 2006-5-24 作者: Kunxing Chen; Xiangqun Cui; Xuefei Gong 收藏 \| 浏览/下载：30/0 \| 提交时间：2013/12/25 Astronomical telescope Mirror truss Node type Assembly and Test