中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共8条，第1-8条

帮助

条数/页：排序方式：
	Multi-objective global optimum design of collaborative robots 期刊论文 OAI收割 STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION, 2020, 卷号: 62, 期号: 3, 页码: 1547–1561 作者: Hu MW(胡明伟); Wang HG(王洪光); Pan XA(潘新安) \| 收藏 \| 浏览/下载：24/0 \| 提交时间：2020/06/13 Finite element substructure method Orthogonal design Collaborative robots Optimum design Gray relational analysis method
	Application of the orthogonal design method in geotechnical parameter back analysis for underground structures 期刊论文 OAI收割 BULLETIN OF ENGINEERING GEOLOGY AND THE ENVIRONMENT, 2016, 卷号: 75, 期号: 1, 页码: 239-249 作者: Tian, Hongming; Chen, Weizhong; Yang, Diansen; Dai, Yonghao; Yang, Jianping \| 收藏 \| 浏览/下载：43/0 \| 提交时间：2018/06/05 Back analysis Orthogonal design method Sensitivity analysis Nelder-Mead method
	Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文 OAI收割 2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China Zi K.; Chen L. 收藏 \| 浏览/下载：20/0 \| 提交时间：2013/03/25 With finite element analysis software Moldflow numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot gas pressure delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding optimum pre-injection shot is 94% gas pressure is 15MPa delay time is 0.5s melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.
	甜菊糖大孔吸附树脂吸附分离工艺条件的正交设计优化期刊论文 OAI收割应用化工, 2011, 卷号: 40, 期号: 6, 页码: 945-948 作者: 刘永峰; 邸多隆; 邸多隆; 黄新异收藏 \| 浏览/下载：18/0 \| 提交时间：2012/10/18 甜菊糖大孔吸附树脂矩阵分析法正交设计 separation macroporous adsorption resin matrix analysis method orthogonal design
	Study of experimental design and Response Surface method for surrogate model of computational simulation (EI CONFERENCE) 会议论文 OAI收割 2nd Annual Conference on Electrical and Control Engineering, ICECE 2011, September 16, 2011 - September 18, 2011, Yichang, China Xi R.; Jia H.; Xiao Q. 收藏 \| 浏览/下载：21/0 \| 提交时间：2013/03/25 While the high-precision simulation is widely used in science and technology Design of Experiment (DOE) based on Response Surface (RS) method can be employed in surrogate model to reduce the cost and error. In order to illustrate the relationship between parameters and response features several DOE methods and Response Surface (RS) method are studied. The author used polynomial regression and RBF neural network based on orthogonal array to build a rocket aerodynamic discipline surrogate model respectively which proved their feasibility. From the results of the test case conclusion is drawn that characteristic as well as acclimatization of DOE methods and different approximation should be considered for different issues so the factors of cost and accuracy could reach a balance synthetically. 2011 IEEE.
	The design of acquisition circuit for grating digital signal based on FPGA (EI CONFERENCE) 会议论文 OAI收割 2010 3rd International Conference on Advanced Computer Theory and Engineering, ICACTE 2010, August 20, 2010 - August 22, 2010, Chengdu, China 作者: Wang W.-G. 收藏 \| 浏览/下载：37/0 \| 提交时间：2013/03/25 In order to resolve the poor suppression capability of noise and fitter interference existing in grating encoder high-rate subdivision and the poor accuracy of kam-to counting circuit the results show that the design method will help improve the controlled object of measurement precision and control accuracy. 2010 IEEE. we design a circuit based on FPGA to realize multiplier kam and filter for the output of two-way orthogonal signal generated by Incremental Optical Encoder. The system is mainly divided into three modules such as filtering multiplier kam-to and counting. The main function of filter circuit is to eliminate the jitter and noise interference existing in the quadrate encoder signals. Kam-to multiplier circuit can accurately judge the full cycle and half-cycle of incremental encoder at the same time can make fourfold multiplier. Counting circuit can use IP cores owned by Quartus II which is not restricted on the median. At last timing simulation based on Modelsim carried on the three modules
	Miniaturize photoelectric stable platform (EI CONFERENCE) 会议论文 OAI收割 2010 International Conference on Computer Application and System Modeling, ICCASM 2010, October 22, 2010 - October 24, 2010, Shanxi, Taiyuan, China Xue W.-Q.; Wang Y.-Y.; Dai M. 收藏 \| 浏览/下载：78/0 \| 提交时间：2013/03/25 In order to reduce the size and weight of the gimbal in a traditional stable platform and correct the disadvantage in size of the payload the paper first improves the gimbal which is an important component of a stable photoelectric platform that also is an important factor in affecting the size and weight of a stability platform. In this paper a closed-form solution of 3-DOF manipulator is designed according mechanical arm design principles. This manipulator is formed by a three joint axes whose extended line is intersected at one point. A standard orthogonal coordinate system is set up for each rod in the manipulator. And then rotation transformation matrix expression is obtained. At last in this paper the manipulator arm-shaped method for solving solutions is description and also each parameter of the gimbal is calculated when the photoelectric detection devices at bottom reach the expected position. Test results show that the photoelectric stability platform with gimbal we designed is smaller lighter and simpler than that traditional. Also the packaging and size of the photoelectric will not be affected with this open structure. 2010 IEEE.
	Exploration in Optimal Design of an Airfoil with a Leading Edge Rotating Cylinder 期刊论文 OAI收割 JOURNAL OF THERMAL SCIENCE, 2010, 卷号: 19, 期号: 4, 页码: 318,325 Yuan-yuan ZHANG1; Dian-gui HUANG1*; Xiao-jing SUN1; Guo-qing WU2 收藏 \| 浏览/下载：25/0 \| 提交时间：2013/01/06 boundary layer control airfoil leading edge rotating cylinder (LERC) numerical simulation design parameters orthogonal optimization method.