中国科学院机构知识库网格系统: 检索

Optimization of the two parameters of classical blaze grating in Littrow mount (EI CONFERENCE) 会议论文 OAI收割
2nd International Conference on Advanced Engineering Materials and Technology, AEMT 2012, July 6, 2012 - July 8, 2012, Zhuhai, China
作者: Zhang S.

收藏 | 浏览/下载：31/0 | 提交时间：2013/03/25

On the base of electromagnetic theory of gratings we analyse the effects of both of two important parameters of classical blaze grating in Littrow mount to diffraction efficiency and the two parameters are optimized for obtaining highest diffraction efficiency. It is presented that not only blaze angle but apex angle affect diffraction efficiency. The investigation has been performed on the design and fabrication of classical blaze grating which has high diffraction efficiency. (2012) Trans Tech Publications Switzerland.

The load analysis of chisel-edge ruling tool for diffraction gratings (EI CONFERENCE) 会议论文 OAI收割
2012 International Applied Mechanics, Mechatronics Automation Symposium, IAMMAS 2012, September 7, 2012 - September 9, 2012, Shenyang, Liaoning, China
作者: zhang f.; zhang f.

收藏 | 浏览/下载：20/0 | 提交时间：2013/03/25

The process of wear design on chisel-edge ruling tool of diffraction gratings is very complex because of following two reasons that one is the load distribution on minute edge area when grating ruling and the other is the anisotropic character of natural diamond. The former is the first step when wear design on chisel-edge ruling tool of diffraction grating In order to predicate the load distribution on minute edge area of tool this paper simulated the load distribution on minute edge area of tool by software when ruling on Aluminum-1100 with tabular data format flow stress and Aluminum-1100 with Power law flow stress respectively and through comparative analysis determined the approximate load distribution on minute edge area of chisel-edge ruling tool that the high load mainly focused on the edge area close to the tip of ruling tool and amount to 200MPa while about to 100MPa on the face of tool. (2012) Trans Tech Publications Switzerland.

Fabrication of high-efficiency ultraviolet blazed gratings by use of direct Ar2-CHF3 ion-beam etching through a rectangular photoresist mask (EI CONFERENCE) 会议论文 OAI收割
International Symposium on Photoelectronic Detection and Imaging 2011: Sensor and Micromachined Optical Device Technologies, May 24, 2011 - May 26, 2011, Beijing, China
Tan X.

收藏 | 浏览/下载：25/0 | 提交时间：2013/03/25

In ultraviolet spectroscopy groove irregularity and surface roughness of nanometer magnitude can cause a significant loss of diffraction efficiency. Therefore there is a constant need to improve the diffraction efficiency. A blazed grating can concentrate most of the light intensity into a desired diffraction order it is important to control the groove shape precisely so it is the optimum choice among gratings of different kinds of profile. As the operating wavelength of most UV spectral applications is less than 200 nm especially the blaze angle and the apical angle. We have presented a direct shaping method to fabricate EUV blazed gratings by using an ion-beam mixture of Ar+ and CHF2 +to etch K9 glass with a rectangular photoresist mask. With this method the required blaze angle is small we have succeeded in fabricating well-shaped UV blazed gratings with a 1200 line/mm groove density and 8.54 blaze angles and 1200 line/mm groove density and 11.68 blaze angles and the metrical efficiency is about 81% and 78%. The good performance of the gratings was verified by diffraction efficiency measurements. When one uses the etching model the conditions on the ion-beam grazing incident angle and the CHF3partial pressure should be noted. Besides since the etched groove shape depends on the aspect ratio of the photoresist mask ridge if we wish to fabricate larger gratings with this method we must improve the uniformity of the photoresist mask before ion-beam etching. 2011 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

The research of rigid lapping technique on diamond grating ruling tool (EI CONFERENCE) 会议论文 OAI收割
2010 International Conference on Materials Science and Engineering Science, ICMSES 2010, December 11, 2010 - December 12, 2010, Shenzhen, China
Jirigalantu A.; Bayanheshig; Dong Q. X.

收藏 | 浏览/下载：28/0 | 提交时间：2013/03/25

One of the effective method of improving diamond tool life on rulling large diffraction gratings is developing precise double-cone edged on line edge transfering tool. But traditional died weight or manual lapping technique couldn't meet the precision requirement of on line edge transfering tool. So preliminary studied rigid lapping of diamond grating ruling tool. Choosing traditional BC6063 shaping machine and made a series of alteration on it achieved the automation of lapping process of diamond grating ruling tool. Through lapping grating ruling tool and AFM measurement find that the surface roughness of tool is 1.51nm the radius of tool edge is 160nm edge quality is good enough this verified the feasibility of rigid lapping of diamond grating ruling tool and lay the foundation for developing precision lapping machine. (2011) Trans Tech Publications Switzerland.

The design of chisel-edge ruling tool for diffraction gratings (EI CONFERENCE) 会议论文 OAI收割
2011 International Conference on Mechatronic Science, Electric Engineering and Computer, MEC 2011, August 19, 2011 - August 22, 2011, Jilin, China
作者: Zhang F.; Zhang F.

收藏 | 浏览/下载：28/0 | 提交时间：2013/03/25

The process of parameters design on chisel-edge ruling tool of diffraction grating which is inefficient and highly costive needs plenty ruling experience came from a series of ruling test to optimize and design it. In order to reduce the choosing range of experiential design parameters on chisel-edge grating ruling tool to improve efficiency and to reduce costs this paper summarize the experimental results of several gratings ruling process for the experiential design on parameters of chisel-edge ruling tool. Provide the specific parameters choosing range as follows: that the blaze angle and directional angle difference in less than 3 the bottom angle and apex angle difference in less than 5. Apex angle larger than the groove bottom angle in conventional grating while apex angle smaller than the bottom angle in echelle grating and the directional angle smaller than blaze angle in both condition. 2011 IEEE.

Autocollimation form dual-frequency laser diffraction grating interferometer design and analysis (EI CONFERENCE) 会议论文 OAI收割
2010 International Conference on Computer, Mechatronics, Control and Electronic Engineering, CMCE 2010, August 24, 2010 - August 26, 2010, Changchun, China
Wang C.-G.

收藏 | 浏览/下载：41/0 | 提交时间：2013/03/25

Propose a new measurement system of autocollimation form laser grating heterodyne interferometer. Take grating diffraction and polarization optics as theoretical foundation second furthermore combined with electronics knowledge to analyze the system. First make use of autocollimation diffraction of grating measurement information obtained by dual-frequency laser belongs to ac signal the interferometer measurement system take grating pitch as measuring datum the structure is simple possess great gain and high signal-noise ratio therefore stable completely overcome the disadvantages of DC level drift caused by light intensity variation of single-frequency laser system can achieve nanometer resolution. 2010 IEEE. reduce the impact of environmental factors easy to install and debug measurement error is small

Manufacture for ruling concave metal grating with a long focal length (EI CONFERENCE) 会议论文 OAI收割
2010 International Conference on Computer, Mechatronics, Control and Electronic Engineering, CMCE 2010, August 24, 2010 - August 26, 2010, Changchun, China
Gao J.-X.

收藏 | 浏览/下载：72/0 | 提交时间：2013/03/25

The ruling technique for concave metal grating with long curvature radius (namely long focal length) is studied. In order to rule the concave grating with a long focal length the diamond carriage with elastic thimble mode is designed and manufactured. It is available not only to rule plane grating but to concave grating with a long focal length. The mathematic expression between the curvature radius of circular arc cutting edge of ruling tools for grating and the curvature radius of concave grating the caliber of grating and the size of transverse direction of bit tool are given. The span of curvature radius of circular arc cutting edge is analyzed theoretically. The concave metal grating with 30m curvature radius for 10.6m laser system is manufactured. The testing result shows that the quality of groove is perfect and the diffraction efficiency is more than 95.6 percent. 2010 IEEE.

Analysis of spectrum narrowing of diode laser bar (EI CONFERENCE) 会议论文 OAI收割
Semiconductor Lasers and Applications III, November 12, 2007 - November 13, 2007, Beijing, China
作者: Liu Y.; Wang L.; Wang L.; Wang L.; Liu Y.

收藏 | 浏览/下载：19/0 | 提交时间：2013/03/25

Laser diode bar (LDB) are used increasingly often for many applications but spectral bandwidth of LDB are generally approximately 2-4nm far too wide for many demanding applications e.g. spin-exchange optical pumping terahertz generation and lidar. External-cavity feedback can improve the spectral properties of LD or LDB. However spectrum narrowing of LDB is more difficult than that of LD. Bar curvature (i.e. "smile") produced in the manufacturing process affects the spectrum narrowing greatly. By geometrical optics approach and ORIGIN software smile which can be corrected by plano-convex cylindrical lens is simulated and the result is in good agreement with experiment. The selection of grating which is also a critical factor of spectrum narrowing will be stated. Finally an external cavity consisting of fast axis collimator two plano-convex cylindrical lens and a diffraction grating is used. The scheme is implemented on a 19-element LDB and yields 3-fold reduction in spectral linewidth under the situation that all optical elements in the system which are not optimized. Further we use a slit in the experiment and analyze the spectrum narrowing of each element in LDB.

基于多台阶反射光栅的飞秒脉冲压缩装置 期刊论文 OAI收割
中国激光, 2008, 卷号: 35, 期号: 7, 页码: 1009, 1012
贾伟; 周常河; 戴恩文

收藏 | 浏览/下载：1573/202 | 提交时间：2009/09/18

衍射与光栅二元光学多台阶反射光栅飞秒激光脉冲脉冲压缩 Binary optics Diffraction and gratings Femtosecond laser pulse Multi-level reflection grating Pulse compression

高精度微结构聚合物光栅的复制技术 期刊论文 OAI收割
中国激光, 2007, 卷号: 34, 期号: 10, 页码: 1363, 1366
王伟; 周常河

收藏 | 浏览/下载：1510/191 | 提交时间：2009/09/18

衍射与光栅 diffraction and grating 微结构光栅 micro-structure grating 光栅复制 grating replication 压印技术 imprint technology