中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共5条，第1-5条

帮助

条数/页：排序方式：
	Sludge Rising and Critical Time Prediction for Denitrification in Secondary Clarifiers: Experimental and Computational Fluid Dynamics Studies 期刊论文 OAI收割 ENVIRONMENTAL ENGINEERING SCIENCE, 2021, 页码: 9 作者: Fan, Long; Xiao, Yao; Liu, Qiao; Xu, Nong; Dong, Qiang \| 收藏 \| 浏览/下载：33/0 \| 提交时间：2021/08/31 computational fluid dynamics (CFD) critical time denitrification lighter sludge sludge rising
	Discriminating cosmic muons and X-rays based on rise time using a GEM detector 期刊论文 OAI收割 CHINESE PHYSICS C, 2016, 卷号: 40, 期号: 8, 页码: 86001 作者: Wu, HY; Zhao, SY; Wang, XD; Zhang, XM; Qi, HR \| 收藏 \| 浏览/下载：30/0 \| 提交时间：2017/07/27 gas electron multiplier cosmic muon X-ray rising time discrimination
	LABTM control system based on FPGA (EI CONFERENCE) 会议论文 OAI收割 2nd International Conference on Mechatronics and Applied Mechanics, ICMAM 2012, December 8, 2012 - December 9, 2012, Taiwan 作者: Wang Y.; Yu P.; Yu P.; Wang Y.; Wang Y. 收藏 \| 浏览/下载：152/0 \| 提交时间：2013/03/25 This paper presents the digital PI control method for design and simulation of a high precision limited angle brushless torque motor control system in Field Programmable Gate Array device (FPGA). The direct drive structures which are widely applied in many servo control fields. Matlab Xilinx System GeneratorR toolbox based on Fixed-Point Arithmetic is used to design the digital PI controller using DSP architecture plot the responses of the control system and generate the VHDL source code. The control system model consists of a digital PI a real LABTM and a real absolute Inductosyn encoder to rpm and position blocks. Through loading generated codes in process of the simulation that built by the digital discrete model it is verified that the rising time of current loop is only 1.2ms and rate loop is 8ms overshoot is rarely 4.2%. Finally the comprehensive positioning accuracy of system can reach up to 5 arc sec and the rate jitter achieves 5% with the 4 arc sec accuracy absolute Inductosyn. (2013) Trans Tech Publications Switzerland.
	Design of transmission of high-speed CCD driving signals (EI CONFERENCE) 会议论文 OAI收割 2011 International Conference on Mechatronic Science, Electric Engineering and Computer, MEC 2011, August 19, 2011 - August 22, 2011, Jilin, China 作者: Zhang S. 收藏 \| 浏览/下载：69/0 \| 提交时间：2013/03/25 In order to overcome the distortion problem of CCD driving signals caused by signal transmission the detail implementation of transmission of high-speed CCD driving signals based on transmission line theory is discussed. The CCD driving signals are critical to the CCD to produce high quality images. In high speed application these drivers will occupy more circuit board areas and can not be put very close to the CCD. So the driving signals must be transmitted. Because the CCD exhibits capacitive load the driving signals distortion problem is much severe. Transmission line theory is used to analyze the problem. The method of source termination is adopted to avoid signal reflections. Meanwhile the characteristic impedance of the circuit board and the resistance of terminal resistor are designed small enough to decrease the rising and falling time of the driving signals. Experimental results show that there is no distortion of the high speed driving signals after transmission. 2011 IEEE.
	Study of microsphere plate photomultiplier tube (EI CONFERENCE) 会议论文 OAI收割 ICO20: Remote Sensing and Infrared Devices and Systems, August 21, 2005 - August 26, 2005, Changchun, China 作者: Wang X.; Li Y.; Li Y.; Li Y.; Li Y. 收藏 \| 浏览/下载：30/0 \| 提交时间：2013/03/25 The photomultiplier tube (PMT) that can work in different wavelength is an important detector device in remote sense technology. Microsphere plate using glass beads 50to 70m in diameter sintered together is the core component of the microsphere plate photomultiplier tube It is a novel two-dimension electron multiplier. The electrons gain for a single plate is about 1017 and do not have the phenomenon of ion-feedback. Furthermore the fabrication process is very easy. In this paper much interest was put on the microsphere plate photomultiplier tube. Based on the analyses from the theory and the experiment result we point out the key technology for fabricating PMT is how to obtain glass beads with narrow range in diameter and how to sinter the glass beads with a sufficient pylome. Factors affect the gradating technology and sintering process along with the solution to them is presented. In the last the structure scheme and technological characteristic for fabricating microsphere plate photomultiplier tube were given. The pulse rising-time of MSP-PMT is below 400ps suitable to the detection of high-speed pulse. As easy to be fabricated and has great advantage over MCP multiplier in the ratio of performance to price the microsphere plate photomultiplier tube is a promising dim-light detector.