中国科学院机构知识库网格
Chinese Academy of Sciences Institutional Repositories Grid
机构
采集方式
内容类型
发表日期
学科主题
筛选

浏览/检索结果: 共4条,第1-4条 帮助

条数/页: 排序方式:
The Mirror Control System of Parabolic Trough Solar Thermal Based on DCS 会议论文  OAI收割
2nd International Conference on Intelligent Materials and Mechatronics and 2nd International Conference on Solar Energy Materials and Energy, Hong Kong, October 29-30, 2015
作者:  
Wang CX(王晨曦);  Liu MZ(刘明哲);  Xu AD(徐皑冬);  Jin N(金妮)
收藏  |  浏览/下载:19/0  |  提交时间:2016/09/13
Ground layer adaptive optics system simulation for the 2.5m telescope in Dome A 会议论文  OAI收割
Amsterdam, Netherlands, 2012-7-1
作者:  
Sijiong Zhang;  Peng Jia
收藏  |  浏览/下载:29/0  |  提交时间:2014/01/09
Non-linear compensation algorithm of LOS locating in aerial remote sensor (EI CONFERENCE) 会议论文  OAI收割
2011 International Conference on Electronic and Mechanical Engineering and Information Technology, EMEIT 2011, August 12, 2011 - August 14, 2011, Harbin, China
作者:  
Li J.;  Li Y.;  Li Y.;  Li Y.;  Li Y.
收藏  |  浏览/下载:34/0  |  提交时间:2013/03/25
A non-linear light-of-sight(LOS) locating compensation algorithm for certain aerial remote sensor is presented in this paper. The LOS locating system is composed of two main components  which are an inertial reference frame to provide coarse LOS locating and a 2-axis Fast Steering Mirror to remove the frame's residual error. The azimuth and elevation of LOS are both affected by the FSM two-degree-of-freedom rotation  which should be dealt with to raise the accuracy of LOS location. This paper extrapolates LOS locating algorithm of FSM by coordinate transformation  and gives corresponding deviation analysis for different LOS poiting angles. It is found that the angle deviation grows rapidly with range of FSM's travel enlarging  so the deviation must be eliminated. Through the data analysis for deviation  a non-linear compensation algorithm is proved effective to reduce the error of LOS significantly. Taking LOS changing in [-3 deg  3 deg] as an example  two analytic expressions are given  and the LOS locating accuracy rises by 34 times compared with non-linear compensation unused  and the cross coupling of LOS loating is 0.08%. 2011 IEEE.  
Study on experiment of grinding SiC mirror with fixed abrasive (EI CONFERENCE) 会议论文  OAI收割
4th International Symposium on Advanced Optical Manufacturing and Testing Technologies: Advanced Optical Manufacturing Technologies, November 19, 2008 - November 21, 2008, Chengdu, China
作者:  
Wang X.;  Zhang X.-J.;  Wang X.;  Wang X.
收藏  |  浏览/下载:23/0  |  提交时间:2013/03/25
A brand-new technology for manufacturing SiC reflecting mirror that is different from the traditional method is adopted  which is called as fixed abrasive surfacing technology. Not only the new method achieves better mirror quality with bigger diamond in diameter quickly  but also because of the fixed motion between the abrasive and workpiece and it will be good for surface finishing. During experiment  material removal characteristic which is on SiC under certain rotation speed and pressure by W7  W5  W3.5  W1.5 pellets has been tested. Through those removal curves  we come to a conclusion that the technology not only has a higher removal rate  but also has much more stability. In addition  the surface roughness experiment is mentioned. In the first stage  we achieved a mirror with surface roughness 42.758nm rms with W7 pellets. The surface roughness is descending as we change pellets with smaller diamond in diameter . At the end of experiment  a smooth surface with roughness 1.591nm rms has been achieved after using W1.5 pellets. Experiment results indicate that the technology which manufactures SiC reflecting mirror with fixed abrasive is able to replace the traditional slurry abrasive completely in certain finishing phase and also has a great foreground in application. 2009 SPIE.