中国科学院机构知识库网格系统: 检索

Research on mirror surface shape of space camera fitting based on SVD 会议论文 OAI收割
Beijing, China, 2019-07-07
作者: Huang, Tuo; Chen, Rong-Li; Chu, Chang-Bo

|

收藏 | 浏览/下载：10/0 | 提交时间：2020/03/04

mirror surface shape Zernike polynomials spherical mirror fitting precision Zernike polynomials terms singular value decomposition

Accuracy synthesis of a 3-RPS parallel robot based on manufacturing costs (EI CONFERENCE) 会议论文 OAI收割
31st Chinese Control Conference, CCC 2012, July 25, 2012 - July 27, 2012, Hefei, China
Yao T.-K.; Xi Z.; Feng Z.; Zhang L.-M.; Yong W.

收藏 | 浏览/下载：32/0 | 提交时间：2013/03/25

Pose accuracy is an important issue for parallel robot being used as mirror supporting system of telescope. One challenging topic is the accuracy synthesis which deals with the optimal design of the manufacturing and assembling tolerances of each component under the given pose accuracy. First the error model of the 3-RPS parallel robot is built based on total derivation of the kinematic equations. And the error variable of each spherical or rotate joint can be expressed as a single boundary error parameter but not three independent position parameters. Then the accuracy synthesis model is formulated taking the manufacturing costs as the optimization objective and the accuracy requirements as the constraint condition. Finally the genetic algorithm is used to solve the optimization problem and a simulation example is given. The results show that the accuracy synthesis method based on manufacturing costs can satisfy the need of pose accuracy and is better for engineering application than the method based on error sensitivity. 2012 Chinese Assoc of Automati.

Nanoscale patterns made by using a 13.5-nm Schwarzschild objective and a laser produced plasma source (EI CONFERENCE) 会议论文 OAI收割
Optical Micro- and Nanometrology IV, April 16, 2012 - April 18, 2012, Brussels, Belgium
作者: Wang X.; Wang X.; Wang X.; Wang Z.; Wang Z.

收藏 | 浏览/下载：37/0 | 提交时间：2013/03/25

Lithium fluoride (LiF) crystal is a very promising candidate as nanometer resolution EUV and soft X-ray detector. Compared with other EUV and soft X-ray detectors charge coupled device and photographic films LiF crystal has high resolution large field of view and wide dynamic range. In this paper using LiF crystal as EUV detector and a Schwarzschild objective (SO) working at 13.5nm as projection optics mesh images with 4.2 m 1.2 m and 800 nm line width and pinhole patterns with 1.5m diameter are acquired in projection imaging mode and direct writing mode respectively. Fluorescence intensity profiles of images show that the resolution of mesh image is 900 nm and the one of pinhole image is 800 nm. In the experiments a spherical condense mirror based on normal incidence type is used to eliminate the damage and contamination on the masks (mesh and pinhole) caused by the laser plasma and the energy density is not decreased compared with that the masks are close to the plasma. The development of the SO the alignment of the objective and the imaging experiments are also reported. 2012 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

Study on spectrograph for ionosphere: A broadband imaging instrument prototype for far-ultraviolet (EI CONFERENCE) 会议论文 OAI收割
International Symposium on Photoelectronic Detection and Imaging 2011: Space Exploration Technologies and Applications, May 24, 2011 - May 26, 2011, Beijing, China
作者: Wang S.-R.; Lin G.-Y.; Yu L.

收藏 | 浏览/下载：35/0 | 提交时间：2013/03/25

Current research on space-based exploration for the ionosphere needs more advanced technologies. Because the spectral signals in the ionosphere distributing basically in the far-ultraviolet waveband are very weak. Usual spectrometer structures and detectors such as CCD can't receive enough information. Based on this principle of atmospheric sounding the imaging spectrometer prototype for ionosphere detection application was designed to solve the problem. This prototype consists of the telescope and the imaging spectrometer. The simple structure and small number of mirrors can help higher transmission efficiency be achieved and weak signals detection be implemented. The telescope is an off-axis parabolic mirror and the spectrometer is a modified Czerny-Turner spectral imaging system. Modified Czerny-Turner spectrometer contains a spherical mirror a fixed plane grating and a toroidal mirror. By adjusting the incident angle to the collimating mirror and using toroidal mirror coma and astigmatism were corrected well. We also optimize distances between the grating to the focusing mirror and the focusing mirror to the image plane to improve disadvantages of traditional Czerny-Turner structure. Designed results demonstrate that aberrations are substantially corrected and high image quality can be obtained in broad waveband. The photon counting Wedge-Strip-Anode detector with micro-channel planes as the receiving plane is accepted for the instrument prototype. The other photon counting 2-D detector responding well for weak light such as Cross-Delay line detector and MAMA detector can also be used for detection. The calibration and performances testing system is made of a vacuum system a deuterium lamp a monochrometer and the instrument prototype. Results obtained from the experiment show that the spectral resolution is 2.4 nm and the spatial resolution is 80 m. The other calibration experiments are running. The technology of the spectrometer prototype is important for the research and applications of ionosphere remote sensing. 2011 SPIE.

Design and wavefront sensing for the segmented Spherical Primary Optical Telescope 会议论文 OAI收割
2011 international conference on electronic and mechanical engineering and information technology, emeit 2011, harbin, china, august 12, 2011 - august 14, 2012
ShengzhangKai; FanXuewu; LiChuang; LiuKai

收藏 | 浏览/下载：18/0 | 提交时间：2012/07/10

high-resolution SPOT on-orbit cophasing segmented spherical primary mirror quasi-Cassegrain telescope wavefront sensing and control Diffraction-limited

Research of active supporting technology based on 400mm thin mirror (EI CONFERENCE) 会议论文 OAI收割
5th International Symposium on Advanced Optical Manufacturing and Testing Technologies: Large Mirrors and Telescopes, April 26, 2010 - April 29, 2010, Dalian, China
作者: Liu X.-Y.; Wang J.-L.; Wang J.-L.; Liu X.-Y.

收藏 | 浏览/下载：27/0 | 提交时间：2013/03/25

Using a spherical mirror of 400mm diameter and 12mm thickness active supporting technology of thin mirror is researched. The axial support of the mirror is composed of 12 active supports and 3 fixed supports. The force actuator which is composed of displacement actuator and force sensor is installed in the active support. The mirror surface is tested by Zygo interferometer. For calibration each actuator exerts unit force alone and the surface variation is tested and taken as the response function of the actuator. The response functions of all actuators compose the stiffness matrix. Then the stiffness matrix is used by damped least square method to determine the correction force of each active support. In order to analyze the correction capability of the active supports 14 Zernike modes of the mirror surface are generated and tested respectively and 7 modes are selected for correction. Initially the RMS error of mirror surface is 1.16 I( =0.6328nm)when all actuators exert the same force. After 5 iterations the RMS error of mirror surface is reduced to 0.13 close to the original surface quality. 2010 Copyright SPIE - The International Society for Optical Engineering.

UV-VUV spectral irradiance responsivity calibration for space remote sensing spectroradiometer (EI CONFERENCE) 会议论文 OAI收割
Advanced Materials and Devices for Sensing and Imaging III, November 12, 2007 - November 14, 2007, Beijing, China
作者: Yu H.

收藏 | 浏览/下载：29/0 | 提交时间：2013/03/25

In order to overcome the irradiance responsivity calibration troubles caused by the weak response of most spectral radiometers in ultraviolet band and poor ratio of signal to noise and to meet special calibration condition for some remote sensing spectroradiometers in space a spectral irradiance responsivity calibration unit based on parallel light illumination mode is established it is composed of a 150W deuterium lamp and a spherical mirror. The calibration unit gets the output standard value of spectral irradiance by irradiance transfer this way avoids the spectral reflectance measurement difficulty of the spherical mirror. A flight spectral radiometer model used for space remote sense was calibrated in range from 160nm to 300nm the calibration error of spectral irradiance responsivity is 4.7%. Some factors which contribute to calibration uncertainties are discussed.

The ELT situation in China 会议论文 OAI收割
Retirement Symposium for Arne Ardeberg on Extremely Large Telescopes - Which Wavelengths, Lund, SWEDEN, 2007-11-29
作者: Liu Z(刘忠); Cui, XQ; Liu Z(刘忠)

收藏 | 浏览/下载：12/0 | 提交时间：2016/04/06

Extremely Large Telescope ground based segment ring aperture Interferometric Telescope active optics adaptive optics spherical mirror site survey Dome A

Developing of in-suit long trance profiler for testing slope error of aspherical optical Elements (EI CONFERENCE) 会议论文 OAI收割
ICO20: Optical Devices and Instruments, August 21, 2005 - August 26, 2005, Changchun, China
Zhou C.; Li H.; Chen C.; Zhou C.; Qian S.

收藏 | 浏览/下载：35/0 | 提交时间：2013/03/25

Profile error of super smooth surface of optical elements at X-ray/EUV in synchrotron radiation (SR) light beam line is described as slope error of them generally. The Long Trace Profiler (LPT) is used for testing surface slope error of SR optical elements in world generally. It is requisite to use In-suit LTP measuring surface thermal distortion of SR optical elements with high heat under high bright SR source. Authors design an In-suit LTP by means of co-path interferometer with pencil light beam. The instrument not only can be used for testing slope error of mirrors in Lab. also in situation test the distortion of mirror with high heat load at synchrotron light beam line. The device can be used to test various absolute surface figures of optical elements such as aspherieal spherical and plane. It is needless standard reference surface. It is named by LTP-III. This paper describes its basic operating principle optical system mechanical constructions DC serve motor control system array detector data acquisition system and computer system for controlling and data analysis of LTP-III. The Instrument has advantages of high accuracy low cost multifunction and wide application. Length of surface measured of optical element accuracy is 0.04 arcsec.

Study on LD-pumped Nd:YAG laser cutter (EI CONFERENCE) 会议论文 OAI收割
ICO20: Lasers and Laser Technologies, August 21, 2005 - August 26, 2005, Changchun, China
作者: Zhang G.; Zhang G.; Zhang G.; Zhang J.; Zhang J.

收藏 | 浏览/下载：23/0 | 提交时间：2013/03/25

The theory of laser cutter and the technology neck is analyzed. We can conclude that it is almost impossible to deal with the waste thick silicon wafers which are yielded in producing silicon wafers by conventional eroding or diamond cutting when the cutting velocity equals 100mm/min while it is also unperfected with ecumenical laser cutter without good beam quality or precise laseroptics system. It is represented that high average power and high repetition rate laser with good beam quality and precise laseroptics system are pivotal to obtain excellent cutting effect such as thick groove depth double-layer 0.75mm thick silicon wafer can be penetrated.. The cross section is fine and the groove is narrow rapid cutting speed the cutting quality meets the expecting demand. fine kerf section without considering the effect of technique. Considering laser medium thermal lens effect and thermal focal length changing with pumping power using plano-convex high reflectivity mirror as the back cavity mirror to compensate the heat lens influence a /4 waveplate to compensate heat -induced birefraction utilize the Nd:YAG self- aperture effect more than 50 W average power 1.064 um IR output is obtained with beam quality factor (M2) equals 3.19. Through the LD-Pumped Nd:YAG laser cutter we developed with short focus length negative spherical aberration focusing lens double axis linear step motor positioning system suitable beam expander multiplying factor appropriate diameter of exit beam aperture proper repetition rate when the cutting velocity equals 400mm/min 0.75mm thick silicon wafer can be penetrated