中国科学院机构知识库网格系统: 检索

浏览/检索结果: 共9条，第1-9条

帮助

条数/页：排序方式：
	LABTM control system based on FPGA (EI CONFERENCE) 会议论文 OAI收割 2nd International Conference on Mechatronics and Applied Mechanics, ICMAM 2012, December 8, 2012 - December 9, 2012, Taiwan 作者: Wang Y.; Yu P.; Yu P.; Wang Y.; Wang Y. 收藏 \| 浏览/下载：152/0 \| 提交时间：2013/03/25 This paper presents the digital PI control method for design and simulation of a high precision limited angle brushless torque motor control system in Field Programmable Gate Array device (FPGA). The direct drive structures which are widely applied in many servo control fields. Matlab Xilinx System GeneratorR toolbox based on Fixed-Point Arithmetic is used to design the digital PI controller using DSP architecture plot the responses of the control system and generate the VHDL source code. The control system model consists of a digital PI a real LABTM and a real absolute Inductosyn encoder to rpm and position blocks. Through loading generated codes in process of the simulation that built by the digital discrete model it is verified that the rising time of current loop is only 1.2ms and rate loop is 8ms overshoot is rarely 4.2%. Finally the comprehensive positioning accuracy of system can reach up to 5 arc sec and the rate jitter achieves 5% with the 4 arc sec accuracy absolute Inductosyn. (2013) Trans Tech Publications Switzerland.
	Analyse the angular velocity estimation errors of -- filter based on high sampling rate (EI CONFERENCE) 会议论文 OAI收割 2011 2nd International Conference on Mechanic Automation and Control Engineering, MACE 2011, July 15, 2011 - July 17, 2011, Inner Mongolia, China 作者: Zhang Y. 收藏 \| 浏览/下载：27/0 \| 提交时间：2013/03/25 In order to get angular velocity of stabilization servo mechanism from angular position sensors -- filter based on high sampling rate was established model and error characteristics were analyzed. With the hypothesis of constant acceleration -- filter and its angular velocity transfer function were deduced. Combing with optimum parameters the effects of and sample rate on the error characteristics were evaluated. According to the requirements of stabilization servo mechanism the frequency characteristics of angular velocity transfer function are analyzed and the filter parameters are designed. The experimental which filter tracked and smoothed sinusoidal signal the results show that when the cutoff frequency of angular velocity loop is 44.9rad/s sampling period and parameters are 0.08ms and 0.01279 respectively the phase leading of angular position is 70. -- filter tracked sinusoidal signals with maximum angular velocity(30/s) and maximum angular acceleration(30/s2) the error of angular velocity estimation was 0.053/s. In the engineering of electro-optical stabilization servo mechanism -- filter can reduce noise effectively and reached the requirement of platform angular velocity estimation. Also it is one of the effective methods to get angular velocity from angular position sensors. 2011 IEEE.
	The angular velocity estimation principal of -- filter based on high sampling rate (EI CONFERENCE) 会议论文 OAI收割 2011 2nd International Conference on Mechanic Automation and Control Engineering, MACE 2011, July 15, 2011 - July 17, 2011, Inner Mongolia, China 作者: Zhang Y. 收藏 \| 浏览/下载：28/0 \| 提交时间：2013/03/25 In order to get angular velocity of stabilization servo mechanism from angular position sensors -- filter and its angular velocity transfer function were predigested. Combing with optimum parameters -- filter based on high sampling rate was established the effect of and sample rate on filter nature frequency were evaluated. According to the requirements of stabilization platform the principle of steady and transient tracking filter differential were proved. With the hypothesis of constant acceleration the frequency characteristics of angular velocity transfer function were analyzed three-dimensional Kalman filter was simplified and the filter parameters were designed. The results show that when the spectrum of input signal was lower than 6rad/s parameters was 0.02 and sampling period were 0.08ms and 0.1ms respectively the filter can realize differential exactly when the spectrum was 9rad/s the precision was no less than 1.1% the phase leading of angular position was no less than 70 the natural frequency should be higher than the cut-off frequency of stabilization platform was two or three times. In the engineering of electro-optical stabilization servo mechanism -- filter has properties of tracking differential and reached the requirement of platform angular velocity estimation. Also it is one of the effective methods to get angular velocity from angular position sensors. 2011 IEEE.
	Position servo control of a DC electromotor using a hybrid method based on model reference adaptive control (MRAC) (EI CONFERENCE) 会议论文 OAI收割 2010 International Conference on Computer, Mechatronics, Control and Electronic Engineering, CMCE 2010, August 24, 2010 - August 26, 2010, Changchun, China 作者: Chen J. 收藏 \| 浏览/下载：23/0 \| 提交时间：2013/03/25 This paper dealed with position control problems of a DC motor servo system that had nonlinear friction and was subject to parametric uncertainties external disturbances etc. In order to overcame those unfavourable factors mentioned above a model reference adaptive control method was proposed to regulate the important and main speed loop in the positioning system which was designed with three closed control loop where a compensatory measure was given so as to counterbalance the friction torque disturbances. In addition the other two close loops were built in adjusting the position and the current of the servo system respectively that aimed to achieve the fast and precise positioning and increase dynamic stiffness against load disturbances. Experimental results illustrate satisfactory performances in steady state error load capability high rapidity and so on. 2010 IEEE.
	Semi-physical simulation of an optoelectronic tracking servo system based on C MEX S functions (EI CONFERENCE) 会议论文 OAI收割 2010 International Conference on Computer, Mechatronics, Control and Electronic Engineering, CMCE 2010, August 24, 2010 - August 26, 2010, Changchun, China Juan C.; Junhong Z. 收藏 \| 浏览/下载：26/0 \| 提交时间：2013/03/25 To the design of an optoelectronic tracking servo system we test the method [1 not only the reasonability of the control algorithm should be considered 2]. The simulation results verify the theoretical analysis. Because C MEX S function has the features of fast execute speed but the cost and time as well. It is necessary to establish the simulation model for the system. Applying the C MEX S functions independently generated program we can build the every independent digital control modules in MATLAB/SIMULINK for the optoelectronic tracking servo system. In the paper directly download to the hardwires we apply the C MEX S function to the design of the practical optoelectronic tracking servo system. For the speed we can design and debug the digital control modules in MATLAB/SIMULINK and then transform and download directly to DSP processor. 2010 IEEE. position loop control and TV delay compensations
	Application of multi-sensors parallel fusion system in photoelectric tracing (EI CONFERENCE) 会议论文 OAI收割 2008 International Conference on Optical Instruments and Technology: Optoelectronic Measurement Technology and Applications, November 16, 2008 - November 19, 2008, Beijing, China Cheng G.-Y.; Cai S.; Gao H.-B.; Zhang S.-M.; Qiao Y.-F. 收藏 \| 浏览/下载：23/0 \| 提交时间：2013/03/25 To solve the real-time and reliability problem of tracking servo-control system in optoelectronic theodolite a multisensors parallel processing system was proposed. Misdistances of three different wavebands were imported into system and then prediction was done in DSP1 to get the actual position information. Data fusion was accomplished in PPGA imported by multi channel buffer serial port. The compound position information was used to control the theodolite. The results were compared with external guide data in DSP2 to implement correction of above calculation and then were imported to epistemic machine through PXI interface. The simulation experiment of each calculation unit showed that this system could solve the real-time problem of feature level data fusion. The simulation result showed that the system can satisfy the real-time requirement with 1.25ms in theodolite with three imaging systems while sampling frequency of photoelectric encoder was 800 Hz. 2009 SPIE.
	Position following control system for the dome based on TMS320F2812 (EI CONFERENCE) 会议论文 OAI收割 ICMIT 2005: Control Systems and Robotics, September 20, 2005 - September 23, 2005, Chongging, China 作者: Zhao J. 收藏 \| 浏览/下载：16/0 \| 提交时间：2013/03/25 A position following control system was discussed to synchronize the rotational position of the dome with that of the theodolite. There were two loops in the servo control system. Open loop control was for speed adjustment while closed loop control was for position following control. The core controller of the servo control system adopted TMS320F2812 DSP (Digital Signal Processing) chip and an absolute type encoder was used as a position feedback unit. A converter DA8562 converted the digital angular position calculated in DSP to an analogy voltage to control the dome rotation through a series of devices such as frequency conversion actiyator servomotor and gear case. The experimental results show that the system synchronous following error less than 2 at 0.1/s to 35/s.
	The advanced position compensation to improve the dynamic tracking ability for fast moving target in an optoelectronic tracking system (EI CONFERENCE) 会议论文 OAI收割 ICO20: Optical Devices and Instruments, August 21, 2005 - August 26, 2005, Changchun, China 作者: Zhao L.; Chen J. 收藏 \| 浏览/下载：17/0 \| 提交时间：2013/03/25 The servo control system of the optoelectronic tracking equipment usually is a kind of SISO. When the fast moving target is tracked the over-tune of the servo system is the main representation for the dynamic tracking error. As the result the tracking ability may be improved by limiting the over-tune. We put forward a method the advanced position compensation (called as APC in short) which is to check the speed-overtune by applying the advanced position information. For the large accelerate target small over-tune tracking is achieved but it lowers the ability for tracking the sine signal at low frequency area. While the dynamic high-type can improve the tracking precision for the sine signal at low frequency area we work out a brand-new method which combines the advantages of the both. It increases the tracking precision in the whole frequency band at large scale for the optoelectronic tracking system. The simulation results show that when the target moves with the largest accelerate 120/s2 120/s the maximum static tracking error is about 0.6.
	开放式机器人控制器结构及其伺服技术研究学位论文 OAI收割工学硕士, 中国科学院自动化研究所: 中国科学院自动化研究所, 1999 端木宁收藏 \| 浏览/下载：71/0 \| 提交时间：2015/09/02 机器人控制器开放式结构位置伺服内核模式驱动程序视觉伺服 robot controller open architecture position servo kernel mode device dricer visual servo